else if((Address < ADDR_FLASH_SECTOR_2) && (Address >= ADDR_FLASH_SECTOR_1)) { sector = FLASH_Sector_1; } else if((Address < ADDR_FLASH_SECTOR_3) && (Address >= ADDR_FLASH_SECTOR_2)) { sector = FLASH_Sector_2; } else if((Address < ADDR_FLASH_SECTOR_4) && (Address >= ...
else if((Address < ADDR_FLASH_SECTOR_2) && (Address >= ADDR_FLASH_SECTOR_1)) { sector = FLASH_Sector_1; } else if((Address < ADDR_FLASH_SECTOR_3) && (Address >= ADDR_FLASH_SECTOR_2)) { sector = FLASH_Sector_2; } else if((Address < ADDR_FLASH_SECTOR_4) && (Address >= ...
else if((Address < ADDR_FLASH_SECTOR_3) && (Address >= ADDR_FLASH_SECTOR_2)) { sector = FLASH_Sector_2; } else if((Address < ADDR_FLASH_SECTOR_4) && (Address >= ADDR_FLASH_SECTOR_3)) { sector = FLASH_Sector_3; } else if((Address < ADDR_FLASH_SECTOR_5) && (Address >= ...
if((Address < ADDR_FLASH_SECTOR_1) && (Address >= ADDR_FLASH_SECTOR_0)) { sector = FLASH_Sector_0; } else if((Address < ADDR_FLASH_SECTOR_2) && (Address >= ADDR_FLASH_SECTOR_1)) { sector = FLASH_Sector_1; } else if((Address < ADDR_FLASH_SECTOR_3) && (Address >= ADDR_...
在STM32F4的编程手册上可找到FLASH的Sector划分,我们现在只操作Main memory: 参考Demo中的例子,将FLASH的页的其实地址(基地址)可定义如下: /* Base address of the Flash sectors */ #define ADDR_FLASH_SECTOR_0 ((uint32_t)0x08000000) /* Base @ of Sector 0, 16 Kbytes */ ...
在STM32F4的编程手册上可找到FLASH的Sector划分,我们现在只操作Main memory: 参考Demo中的例子,将FLASH的页的其实地址(基地址)可定义如下: /* Base address of the Flash sectors */ #define ADDR_FLASH_SECTOR_0 ((uint32_t)0x08000000) /* Base @ of Sector 0, 16 Kbytes */ ...
Forinformationonprogramming,erasingandprotectionoftheinternalFlashmemory pleaserefertotheSTM32F40xandSTM32F41xFlashprogrammingmanual. ForinformationontheARMCortex™-M4Fcore,pleaserefertotheCortex™-M4FTechnical ReferenceManual. Relateddocuments Availablefrom.arm: ...
STM32F207内部Flash编程详解 本文将根据ST官方Flashprogramming manual,文档编号:PM0059,讲解STM32F207内部Flash编程。 01概述 这里的flash是指STM32F207内部集成 2021-02-23 15:59:32 STM32F4时钟配置的操作步骤 本文将介绍STM32F4时钟配置的操作步骤、并对比时钟配置前后LED外设闪烁的快慢以及对应代码的讲解。 2023-04...
STM32F407VGT6 microcontroller featuring 1 MB of Flash memory, 192 KB of RAM in an LQFP100 package ? On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-LINK/V2 (with SWD connector for programming and debugging) ? Board power supply: through USB bus or ...
Forinformationonprogramming,erasingandprotectionoftheinternalFlashmemory pleaserefertotheSTM32F40xandSTM32F41xFlashprogrammingmanual. ForinformationontheARMCortex™-M4Fcore,pleaserefertotheCortex™-M4FTechnical ReferenceManual. Relateddocuments Availablefrom.arm: ■Cortex™-M4FTechnicalReferenceManual,available...