Please check your Tools->Board setting.#endif//These define's must be placed at the beginning before #include "STM32TimerInterrupt.h"//_TIMERINTERRUPT_LOGLEVEL_ from 0 to 4//Don't define _TIMERINTERRUPT_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.//Don't ...
登录后复制1staticvoid timer_setup(void)2{3/* Enable TIM3clock. */4rcc_periph_clock_enable(RCC_TIM3);56/* Enable TIM3interrupt. */7nvic_enable_irq(NVIC_TIM3_IRQ);89/* Timer global mode:10* - No divider11* - Alignment edge12* - Direction up13*/14timer_set_mode(TIM3, TIM_CR1_...
看门狗,又叫 watchdog timer,是一个定时器电路, 一般有一个输入,叫喂狗(kicking the dog or service the dog),一个输出到MCU的RST端,MCU正常工作的时候,每隔一端时间输出一个信号到喂狗端,给 WDT清零,如果超过规定的时间不喂狗(一般在程序跑飞时),WDT 定时超过,就会给出一个复位信号到MCU,是MCU复...
Use Arduino Library ManagerThe best and easiest way is to use Arduino Library Manager. Search for STM32_TimerInterrupt, then select / install the latest version. You can also use this link for more detailed instructions.Manual InstallAnother way to install is to:Navigate to STM32_TimerInterrupt...
fix: arduino legacy ide warning by @fpistm in #2578 chore(c0): enable usb by @fpistm in #2584 chore(c0): update to latest STM32CubeC0 v1.3.0 by @fpistm in #2587 chore(u0): update to latest STM32CubeU0 v1.2.0 by @fpistm in #2588 chore(h5): update to latest STM32CubeH5 ...
介绍:基于stm32f103c8t6 核心板(淘宝上到处都是的开发板),使用 STM32CubeMX软件和Keil进行开发,实现了 GPIO输出,Timer Interrupt 定时器中断 cherry1989 2021-08-09 09:07:14 STM32F103C8T6定时器配置 这一章讲的是STM32F103C8T6定时器配置,定时器配置主要要弄懂的是系统主频多少、你分频多少、你需要定时多长...
Up to 82 fast I/Os with interrupt capability most 5 V-tolerant and up to 14 I/Os with independent supply down to 1.08 V Up to 15 timers and 2 watchdogs 1x 16-bit advanced motor‑control, 3x 32‑bit and 3x 16‑bit general purpose, 2x 16‑bit basic, 4x low‑power 16...
标准的I2C协议,OLED显示程序 创建字模库,来对应客户的学号+姓名 I2C协议来初始化OLED显示屏 添加到main函数,进行仿真测试 项目主函数展示 代码语言:javascript 代码运行次数:0 #include"stm32f10x.h"#include"OLED_I2C_sim.h"#include"delay.h"#include"timer.h"#include"DS3231.h"#include"interrupt.h"#includ...
8 timers: 16-bit for advanced motor control, four 16-bit general-purpose, two watchdogs, SysTick timer Calendar RTC with alarm and periodic wakeup from Stop/Standby Communication interfaces Two I2C-bus interfaces supporting Fast-mode Plus (1 Mbit/s) with ...
我在很长一段时间后回到Arduino,我想尽可能接近裸机,同时仍然使用Arduino Uno作为ISP。我决定首先使用ATTiny85作为频率计数器,使用TImer0对T0引脚上的脉冲进行计数: /* * Inputs: Frequency source{} //Almost everything is handled by interrupt 浏览75提问于2020-12-27得票数 0 2回答 利用STM32硬件电路定时器...