针对“stm32 cannot enter debug mode”的问题,以下是一些可能的解决方法和步骤: 检查并安装正确的驱动: 确保你的开发板(如ST-Link)已经安装了正确的USB驱动。有时驱动未正确安装或版本不匹配会导致无法进入调试模式。 对于ST-Link,你可以尝试在Keil的安装目录中找到ST-Link的USB驱动(如C:\..\ARM\STLink\USB...
方法之二是使用STVP(同时使用STLINK),STVP在jitg连接之前会拉一下目标芯片的 ...你好,我的stm32...
st-info:errorwhileloadingsharedlibraries: libstlink.so.1: cannotopensharedobjectfile: No suchfileordirectory 运行一下sudo ldconfig可以解决问题 通过st-info 检查 会提示无法进入 SWD 模式 $ st-info --probe Failed to parse flashtypeor unrecognized flashtype Failed to enter SWD mode Found 1 stlink ...
I am trying no code project just confirm enter debugger works. STM32F103C8T6 STM32Cube IDE 1.9 I Get ST-Link Error When attempting to debug. Reason(18) Could not verify ST device! Abort connection. Error halting cpu. See attached. Any suggestions? Open On-Chip Debugger 0.11.0+dev-...
voidUSBPD_DPM_Notification(uint8_tPortNum,USBPD_NotifyEventValue_TypeDefEventVal){/* USER CODE BEGIN USBPD_DPM_Notification */USBPD_StatusTypeDefstatus;switch(EventVal){caseUSBPD_NOTIFY_STATE_SRC_READY:{/* Request a PRS to SNK */status=USBPD_DPM_RequestPowerRoleSwap(PortNum);break;}/* US...
支持Jlink、CMSIS-DAP、ST-Link调试器。 生成.vscode/c_cpp_properties.json配置文件,便于在VSCode浏览、编辑STM32CubeMX生成的工程代码 在Core/Src/main.c中生成同时适用于Keil MDK和GCC编译器的重定向函数 优化Makefile类型的编译输出: compiling Core/Src/sysmem.c... ...
我用STLINK调试STM32程序,点击DEBUG,运行以后,出现以下提示。请问高手,如何解决?谢谢 ...
Step 6. Click Build 'Debug', and it should compile without any errorsStep 7. Open STM32CubeProgrammer, connect ST-LINK to your PC, hold RESET Button of your Device, then click Connect and release RESET Button:Step 8. Make sure the Read Out Protection is AA, if it is shown as BB, ...
Can Cube monitor work with STM32 sleep mode? during sleep mode, the debug bloc is not able to access the memory and returns 0. So the tool can not be used during sleep mode. Can CubeMonitor and IDE debugging run at the same time? Yes, through ST-Link server that allow...
TDTS = Tck_tim TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上计数模式 TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure); //根据指定的参数初始化TIMx的时间基数单位 TIM_ITConfig(TIM3,TIM_IT_Update,ENABLE ); //使能指定的TIM3中断,允许更新中断 //中断优先级NVIC设置 NVIC...