命令 说明 show counters 显示协议栈计数器。 show cpu 显示CPU 利用率信息。 show clns 要显示 IS-IS 的无连接模式网络服务 (CLNS) 信息,请使用 show clns 命令。 show clns { filter-set [ name] | interface [ interface_name] | is-neighbors [ interface_name [ detail] ...
Clear命令中最主要的是Clear counters命令。对于端口收发的各计数器的刷新必须使用Clear counters,可通过show interface命令来观察。 Clear命令适用场合如下: 许多情况下,我们需要使用带参数的Ping命令来测试链路的通断,同时在一段时间内Ping后,通过Show ip interface x/x counters命令来查看端口报文的收发及CRC校验等情况...
show access-lists命令用于显示设备的访问控制列表(ACL)信息。这个命令可以帮助你了解设备的ACL配置。 Router# show access-lists 返回示例: Standard IP access list 1 10 permit 192.168.1.0, wildcard bits 0.0.0.255 (10 matches) Extended IP access list 100 10 permit ip any any (20 matches) 20 deny ...
clear nat counters 清除NAT 策略计数器。 show nat 显示NAT 策略的运行时间表示。 show nat pool 要显示 NAT 池使用情况的统计信息,请使用 show nat pool 命令。 show nat pool [ interface if-name [ ip address ] | ip address | detail ] show nat pool cluster [ summary...
Access-group 把访问控制列表(ACL)应用到接口上Access-list 定义一个标准的IP ACL Access-template 在连接的路由器上手动替换临时访问列表入口 Appn 向APPN子系统发送命令 Atmsig 执行ATM信令命令 B 手动引导操作系統 Bandwidth 设置接口的带宽 Banner motd 指定日期信息标语 ...
I presume you are talking about ACL counters if so the please read the following (from a previous post of mine) Try command: > clear access-list counters This clears the counters shown by the show access-list command. To clear counters on an interface, go i...
system-access-list—Show all system-access-list configurations tls-global—Show all tls-global configurations inventory—Display an inventory of all configured elements on the Oracle Communications Session Border Controller Example Copy ORACLE# show configuration snmp-community show directory This command...
show access-lists命令用于显示设备的访问控制列表(ACL)信息。这个命令可以帮助你了解设备的ACL配置。 Router# show access-lists 返回示例: Standard IP access list 1 10 permit 192.168.1.0, wildcard bits 0.0.0.255 (10 matches) Extended IP access list 100 ...
Last clearing of"show interface"counters never Input queue:0/75/0/0(size/max/drops/flushes);Total output drops:0Queueing strategy: fifo Output queue:0/40(size/max)5minute input rate0bits/sec,0packets/sec5minute output rate0bits/sec,0packets/sec1packets input,64bytes,0no buffer ...
首先使用Clearcounters命令清空统计值,然后使用一系列Ping命令使路由器端口收发报文,最后使用Show命令来查看统计值。 排障案例① 通过Show interface FastEthernet 0/13 counters观察到端口有如下统计数据: Interface : Fa0/13 5 minute input rate : 76208 bits/sec, 53 packets/sec ...