zzPresstheopqrbuttonsorInfoList](eitherpresstheop3OtherShooting Modes turnthe7dialtochoosethepersontobuttonsorturnthe7dial),andthen checkoredit,andthenpressthempressthembutton.Onthescreen4PMode button.displayed,choosefaceinformationto5Tv,Av,M,and erasebypressingtheopqrCMode buttonsandthenthembutton.After...
P2622 ( Parameter ) 依赖于不同的Job,对应不同的Job有不同的含义(参见List Manual) P2623.8/9 ( Mode ) 定义定位方式,仅当任务 ( Job )为位置方式 ( Position ) 时有效 P2617/P2618/P2619/P2620 ( Position, Velocity, Acceleration, Deceleration ) 指定运动的位置,速度,加/减速 P2623.4/5/6 ( Adv...
SINAMICSSINAMICS S120/S150 List Manual06/2020 EditionList Manual06/2020 Editionwww.siemens.com/drives 阅读了该文档的用户还阅读了这些文档 2 p. SIEMENS西门子 SIMATIC IPC RC-543B快速安装指南 365 p. SIEMENS西门子 SINUMERIK 828D PPU 和组件设备手册 328 p. SIEMENS西门子 S7-1200 G2 可编程控制器...
SINAMICS S List Manual (LH1), 07/2007 故障与报警 故障与报警列表 F01036 (A) ACX: 参数备份文件丢失 驱动单元: 所有设备 故障动作: A_INFEED : NONE (OFF2) SERVO : NONE (OFF1, OFF2, OFF3) VECTOR : NONE (OFF1, OFF2, OFF3) 故障确认: 立即动作 原因: 当下载参数的时候,一个与驱动...
FunctionManual03/2006Edition sinamics SINAMICSS120 Infeed1 ExtendedSetpointChannel2 OperatingModes3 ExtendedFunctions4 SINAMICSS120 BasicInformation AbouttheDriveSystem5 FunctionManual Availabilityof SWFunctionsA ListofAbbreviationsB ReferencesC IndexD Validfor ...
P2622 ( Parameter ) 依赖于不同的Job,对应不同的Job有不同的含义(参见List Manual)P2623.8/9 ( Mode ) 定义定位方式,仅当任务 ( Job )为位置方式 ( Position ) 时有效P2617/P2618/P2619/P2620 ( Position, Velocity, Acceleration, Deceleration ) 指定运动的位置,速度,加/减速P2623.4/5/6 ( Advance...
S120 装置能否直接读取编码器的实时脉冲数,以便用PLC 控制器来实现控制、定位等功能。 回答:S120 装置中参数r0482可显示编码器的实际增量值。r2521是驱动在激活基本定位功能后的实际位置值,单位是LU。r0482 是32位的双字,参考S120 List manual中的功能图4704: 图1. 可以通过拆解r0482 的方法得到实时的脉冲数。
Commissioning• STARTER parameterization and commissioning tool • SINAMICS S120 Getting Started • SINAMICS S120 Commissioning Manual • SINAMICS S120 CANopen Commissioning Manual • SINAMICS S120 Function Manual • SINAMICS S List Manual • SINAMICS S150 operating instructions Usage/operation• ...
P2622 ( Parameter ) 依赖于不同的Job,对应不同的Job有不同的含义(参见List Manual)P2623.8/9 ( Mode ) 定义定位方式,仅当任务 ( Job )为位置方式 ( Position ) 时有效P2617/P2618/P2619/P2620 ( Position, Velocity, Acceleration, Deceleration ) 指定运动的位置,速度,加/减速P2623.4/5/6 ( Advance...
SINUMERIKSINUMERIK840DslSINAMICSS10MachinedataandparametersListManualValidfor:ControlSINUMERIK840Dsl/840DEslSoftwareCNCsoftwareVersion4.95SP1SINAMICSS10Version5.SP3HF901/06FC5397-7AP40-6BA6Introduction1FundamentalsafetyinstructionsSINUMERIKmachineandsett