File "example.py", line 1, in<module>import smbus ModuleNotFoundError: No module named 'smbus' 1. 2. 3. 这个错误表明Python环境中缺少smbus模块。 错误现象的时序可以通过以下图示表示: Python环境开发者Python环境开发者执行smbus相关代码报错信息(ModuleNotFoundError) 很多开发者在面对这个错误时,往往...
time.sleep(2) ser.write(b'H') time.sleep(1) ser.write(b'L') 三、I2C/SPI总线 I2C和SPI是常用的总线协议,用于与各种传感器、显示器等外围设备通信。 1、使用smbus2库进行I2C通信 smbus2是一个Python库,用于I2C通信,适用于Raspberry Pi等设备。 import smbus2 import time 初始化I2C总线 bus = smbu...
pip install smbus2 I2C通信示例: from smbus2 import SMBus 打开I2C总线 bus = SMBus(1) address = 0x48 # 设备地址 读取数据 data = bus.read_byte_data(address, 0x00) print(f"Received data: {data}") 关闭I2C总线 bus.close() 3、使用spidev库进行SPI通信 spidev是一个Python库,用于SPI通信。
fromsmbus2importSMBuswithSMBus(1)asbus:# Write a byte to address 80, offset 0data=45bus.write_byte_data(80,0,data) Example 4: Write a block of data It is possible to write 32 bytes at the time, but I have found that error-prone. Write less and add a delay in between if you...
1.启动RPi串行I2C接口及安装Python SMBus库 2. 树莓派与AT24C02 EEPROM接口实验电路 3. Python SMBus库函数介绍 4. 使用I2C Tools及Python SMBus读写AT24C02 EEPROM 一、I2C接口技术 I2C接口是嵌入式系统中常用的网络接口之一,它采用串行通信方式将MCU/传感器连接到系统总线,通过主机/从机的方式协调工作。
一、I2C接口技术 1.I2C总线系统组成 2.I2C总线的状态及信号 3.I2C总线基本操作 4.启动和停止条件 5.I2C总线数据传输格式 二、I2C总线上拉电阻的估算与选取 三、树莓派与AT24C02接口实验电路及PythonSMBus串行I2C EEPROM应用编程 1.启动RPi串行I2C接口及安装Python SMBus库 2. 树莓派与AT24C02 EEPROM接口实验电路 ...
from smbus3 import SMBus with SMBus(1) as bus: bus.set_retries(5) # Retry up to 5 times b = bus.read_byte_data(80, 0) print(b) Example 2: Read a block of data You can read up to 32 bytes at once. from smbus3 import SMBus with SMBus(1) as bus: # Read a block of...
= smbus.SMBus(I2C port no.) I2C port no:I2C端口号。即0或1 Example – Bus=smbus.SMBus(1) 现在,我们可以使用Bus对象访问SMBus类。 Bus.write_byte_data(Device Address, Register Address, Value) 该函数用于将数据写入所需的寄存器。 Device Address :7位或10位器件地址 ...
smbus: System Management Bus protocol i2c: Inter-Integrated Circuit protocol support spi: Serial Peripheral Interface support Hardware protocol specifications: ProtocolSpeed RangeMax Distance I2C 100kHz – 5MHz 1-2 meters SPI 20MHz – 60MHz 10-20 cm Serial 300bps – 115200bps 15 meters USB 1.5Mbp...
VCC 和 GND 分别连接到 Pi 的#2 和#6 引脚,SDA 和 SCL 连接到 Pi 的#3 和#5 引脚。您现在已经准备好使用smbus库来读取指南针,使用一点数学(eek!)以基于感测到的 x 和y 值来计算方位。现在是使用之前提到的i2cdetect工具的好时机,以确保你可以从指南针上读取。通过键入sudo i2cdetect -y 1运行该工具...