R2(config)#router eigrp 1 R2(config-router)#no auto-summary R2(config-router)#network 172.16.0.0 3查看eigrp邻居 R1(config-router)#do show ip eig nei IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime
filter-policy { ipv4-acl-number | prefix-list prefix-list-name } export [ bgp | direct | eigrp [ eigrp-as ] | { isis | ospf | rip } [ process-id ] | static ] 缺省情况下,不对引入的路由信息进行过滤。 (5) 配置路由引入时的参数缺省值(开销、标记、类型)。 default { cost cost-value...
重新向OSPF引入外部路由 reset ospf [ process-id ] redistribution 1.13 典型配置举例 1.13.1 OSPF基本功能配置举例 1. 组网需求 · 所有的路由器都运行OSPF,并将整个自治系统划分为3个区域。 · 其中Router A和Router B作为ABR来转发区域之间的路由。 · 配置完成后,每台路由器都应学到AS内的到所有网段的路...
EIGRPOSPFBGPRedistributionAdministrative distanceConvergencePacket delayThroughput.Routing is the process of data path selection of IP networks. Routers perform path selection on the basis of routing tables stored in their memory. Routing table contains IP routes for route transformation via the best path...
R2(config-router)#do show ip eigrp nei IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 172.16.12.1 Se1/1 11 00:13:15 113 1017 0 3 邻居关系可以成功建立, R1#show ip eigrp int 1 ...
R2(config)#router eigrp 1 R2(config-router)#no auto-summary R2(config-router)#network 172.16.0.0 3查看eigrp邻居 R1(config-router)#do show ip eig nei IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq
Configuration EIGRP 配置EIGRP,首先在全局配置模式下使用router eigrp [AS号]命令.接下来再使用network命令定义直接相连的网络.仍然可以像配置IGRP那样使用passive-interface命令来禁止某个接口接收或发送Hello信息.并且记住EIGRP的AD是90 来看1个配置实例,如图: Router Network Address Interface Address RouterA 192.168.10....
redistribute eigrp 100 subnets route-map B2A network 172.16.0.0 0.0.0.3 area 1 ip prefix-list B2A description OSPF-EIGRP_Redistribution ip prefix-list B2A seq 5 permit 10.10.5.0/24 ip prefix-list B2A seq 10 permit 10.10.6.0/24 ip prefix-list A2B description EIGRP-OSPF_Redistrib...
FTD可以将路由从一个OSPF进程重新分发到另一个OSPF进程。重分发也可以从RIP、BGP、EIGRP(7.2+版本)、静态路由和连接路由重分发到OSPF路由进程。 1. 要配置OSPF重分发,请导航到设备>设备管理>编辑设备。 2. 单击路由 3. 单击OSPF。 4. 选择Redistribution > Add。
您可以選擇配置路由重分發。Cisco ASA可以將RIP和EIGRP發現的路由重分發到OSPF路由進程中。您還可以將靜態路由和連線的路由重新分發到OSPF路由進程。在Redistribution窗格中定義路由重分發。 OSPF hello資料包作為組播資料包傳送。如果OSPF鄰居位於非廣播網路中,則必須手動定義該鄰居。手動定義OSPF鄰居時,Hello資料包將作為...