nmap [Scan Type(s)] [Options] {target specification} 命令参数分为三个部分，Scan Types 指探测类型，如 -PS 指 TCP SYN Ping，-PA 指 TCP ACK Ping，-PU 指 UDP Ping 等等；Options 指探测选项，如 -n 指不对活动的 IP 地址进行反向域名解析，用以提高扫描速度，-R 指对活动的 IP 进行反向域名解...
nmap -S [srcip] -d –max-scan-delay 10 -oAlogs/tcp-allports-%T-%D -iL tcp-allports-1M-IPs –max-retries 1–randomize-hosts -p- -PS21,22,23,25,53,80,443 -T4 –min-hostgroup 256 –min-rate175 –max-rate 300 上述命令用于扫描互联网上100万台主机全部的TCP端口的开放情况。 使用...
-F: Fast mode - Scan fewer ports than the default scan -r: Scan ports consecutively - don't randomize --top-ports <number>: Scan <number> most common ports --port-ratio <ratio>: Scan ports more common than <ratio> SERVICE/VERSION DETECTION: -sV: Probe open ports to determine service...
--top-ports <number>: Scan <number> most common ports --顶部端口<编号>:扫描<编号>最常见的端口 --port-ratio <ratio>: Scan ports more common than <ratio> --端口比率<比率>:扫描比<比率>更常见的端口 服务/版本检测: -sV:探测打开的端口以确定服务/版本信息 --version-intensity <level>: Set ...
Scan <number> most common ports --port-ratio <ratio>: Scan ports more common than <ratio> SERVICE/VERSION DETECTION: -sV: Probe open ports to determine service/version info --version-intensity <level>: Set from 0 (light) to 9 (try all probes) --version-light: Limit to most likely pr...
Scan <number> most common ports --port-ratio <ratio>: Scan ports more common than <ratio> SERVICE/VERSION DETECTION: -sV: Probe open ports to determine service/version info --version-intensity <level>: Set from 0 (light) to 9 (try all probes) --version-light: Limit to most likely pr...
Example 1. A representative Nmap scan # nmap -A -T4 scanme.nmap.org # nmap有个典型参数实例"raw IP packets",参数"-A",用于启用操作系统和版本检测,脚本扫描、和追踪路线,参数"-T4"是指快速执行;参数"raw IP packets" 是要扫描的主机名。
details when version detection has been requested. When an IP protocol scan is requested (-sO), Nmap provides information on supported IP protocols rather than listening ports. #nmap根据不同的输入选项,输出不同的扫描结果列表。列表列出了端口、协议、服务名称和状态,状态有开放、过滤、已关闭、未过滤,...
-- Scan open ports local portTable = {80, 443, 8080} local openPorts = {} for _, port in ipairs(portTable) do local status, err = nmap.scan_port(host, port) if status == "open" then table.insert(openPorts, port) end
--allports (Don't exclude any ports from version detection) --version-intensity <intensity> (Set version scan intensity) 版本扫描强度 --version-light (Enable light mode) 相当于 --version-intensity 2 --version-all (Try every single probe) 相当于 --version-intensity 9 ...