配置网络接口:编辑网络接口的配置文件,该文件位于/etc/network/interfaces或/etc/sysconfig/network-scripts/ifcfg-<interface>中。在文件中找到相应的网卡接口,添加以下行来配置网关服务器: auto <interface> iface <interface> inet static address <ip_address> netmask <subnet_mask> gateway <gateway_ip> 将<inter...
第3行中的get-mac-address.sh也在/usr/share/doc/ifupdown/examples/目录里,也同样要加可执行权限。这个脚本的作用,就是获得每块网卡的MAC地址。 这段配置首先配置了两个逻辑接口(这个名词的定义请参见debian参考手册http://www.debian.org/doc/manuals/reference/ch-gateway.zh-cn.html)lan和internet,然后根据网...
} //get the gateway of this interface memset(query_cmd,0,(query_cmd)); sprintf(query_cmd," | grep %s | tail -1 | awk {'print '} > ./gateway",bufif_i].ifr_name); system(query_cmd); query_fd = fopen("/gateway", "r+"); if!query...
如果是手动配置它, 则类似以下内容将设置 default gateway(network, broadcast 和 gateway是可选的): autoeth0ifaceeth0inetstaticaddress192.168.0.7netmask255.255.255.0gateway192.168.0.254 设置速度与双工(duplex) 某些网络中, 无法进行自动协商. 如果必须手动设置接口的速度和双工, 则可能需要反复尝试. 以下是基本步...
route[-f][-p][Command[Destination][mask Netmask][Gateway][metric Metric]][ifInterface]] -f清除所有网关入口的路由表。-p与add命令一起使用时使路由具有永久性。Command指定您想运行的命令 (Add/Change/Delete/Print)。Destination指定该路由的网络目标。mask Netmask指定与网络目标相关的网络掩码(也被称作子网...
Gateway:该网段是通过那个 gateway 连接出去的, 如果显示 0.0.0.0 表示该路由是直接由本机传送,亦即可以透过局域网络的 MAC 直接通信; 如果有显示 IP 的话,表示该路由需要经过路由器的帮忙才能够传送出去。 Flags:总共有多个标志,代表的意义如下: U (route is up):该路由是启动的; H (target is a host):目...
GATEWAY#=NEXTHOP 8. 给接口配置多个地址: ip addr之外,ifconfig或配置文件都可以; (1) ifconfig IFACE_LABEL IPADDR/NETMASK IFACE_LABEL: eth0:0, eth0:1, ... (2) 为别名添加配置文件; DEVICE=IFACE_LABEL BOOTPROTO:网卡别名不支持动态获取地址; ...
When the router also has the third network interface with an Internet uplink, this same setup allows Internet access for all hosts on both subnets because they’re configured to use the router as the default gateway. But that’s where things get more complicated. The problem is that certain...
GATEWAY: 默认网关; DNS1:第一个DNS服务器指向; DNS2:第二个DNS服务器指向; USERCTL:普通用户是否可控制此设备; PEERDNS:如果BOOTPROTO的值为“dhcp”,是否允许dhcp server分配的dns服务器指向信息直接覆盖至/etc/resolv.conf文件中; ifcfg文件示例:
sudo ip route adddefaultvia [ip-address] dev [interface] 例如,要添加通过ens33 将流量定向到路由器192.168.30.1的默认路由,命令为: sudoiprouteadddefaultvia192.168.30.1devens33iprouteget[ip-address] 要删除路由表条目,请使用以下语法: sudoiproutedelete[network-address]via[gateway-ip] ...