up route add -net 10.0.3.0 netmask 255.255.0.0 gw 10.0.2.1 在RHEL / CentOS 上添加永久路由配置 需要在/etc/sysconfig/network-scripts目录中创建一个名为route-<device>的配置文件 使用nmcli $ sudo nmcli connection modify <interface_name> +i
sudoifconfig<interface>inet6add<ipv6_address>/<prefix_length> 将<interface>替换为要配置的网络接口的名称,<ipv6_address>替换为您要分配的IPv6地址,<prefix_length>替换为前缀长度。 例如,要将IPv6地址为2001:0db8:85a3:0000:0000:8a2e:0370:7334,前缀长度为64的IPv6地址分配给eth0接口,执行以下命令: ...
route add -host 192.168.1.123 dev eth0 route add -host 192.168.1.123 gw 192.168.1.1 # 加入到网络的路由 route add -net 192.168.1.123 netmask 255.255.255.0 eth0 route add -net 192.168.1.123 netmask 255.255.255.0 gw 192.168.1.1 route add -net 192.168.1.123 netmask 255.255.255.0 gw 192.168.1.1...
例:route add default gw mango 格式:route add -net {NETWORK-ADDRESS} netmask {NETMASK} dev {INTERFACE-NAME} 添加到指定网络的路由规则,其中 参数{NETWORK-ADDRESS}: 用于指定网络地址 参数{NETMASK}: 用于指定子网掩码 参数{INTERFACE-NAME}: 用于指定接口名称,如eth0。 例1:route add -net 192.56.76.0 ...
# Add non interface-specific static-routes. if[ -f /etc/sysconfig/static-routes]; then grep"^any"/etc/sysconfig/static-routes| whilereadignore args ; do /sbin/routeadd -$args done fi 则,如果要添加一条静态路由,命令为: routeadd-net192.56.76.0 netmask255.255.255.0 dev eth0 ...
这段配置首先配置了两个逻辑接口(这个名词的定义请参见debian参考手册http://www.debian.org/doc/manuals/reference/ch-gateway.zh-cn.html)lan和internet,然后根据网卡的MAC地址,将逻辑接口映射(mapped)到物理接口上去。 再来看下面这段配置: auto eth0 ...
# Add non interface-specific static-routes. if[ -f /etc/sysconfig/static-routes]; then grep"^any"/etc/sysconfig/static-routes| whilereadignore args ; do /sbin/routeadd -$args done fi 1. 则,如果要添加一条静态路由,命令为: route add -net 192.56.76.0 netmask 255.255.255.0 dev eth0 ...
route add -net 10.10.1.0/24 10.10.1.1 与Linux 类似,但是网关没有 gw 参数(同 macOS) 永久: vi /etc/rc.conf Set default router IP to 60.1.2.3: defaultrouter="60.1.2.3" Create static routing for lan network 192.168.1.0/24, append following two lines: ...
/bin/sh action=$1 interface=$2 logger "$0: Action: $action, interface: $interface." if [ "x$action" == "xpre-up" ]; then logger "$0: Set $interface EGRESS priority mappings 0:3 1:3 2:3 3:3 4:3 5:3 6:3 7:3." ip link set $interface type vlan egress 0:3 1:3 2:...
Assigning anIP AddressandGatewayto interface on the fly. The setting will be removed in case of system reboot. # ifconfig eth0 192.168.50.5 netmask 255.255.255.0 Enable or Disable Specific Interface Toenableordisablespecific Interface, we use example command as follows. ...