Linux Commandethtool 显示或修改以太网卡的配置信息 补充说明 ethtool命令用于获取以太网卡的配置信息,或者修改这些配置。这个命令比较复杂,功能特别多。 语法 ethtool [ -a | -c | -g | -i | -d | -k | -r | -S |] ethX ethtool [-A] ethX [autoneg on|off] [rx on|off] [tx on|off] ...
In most Linux distributions, the ‘ethtool’ command comes pre-installed. However, if it’s not, you can install it in Debian based distributions like Ubuntu, by running the commandsudo apt-get install ethtool. For RPM-based distributions like CentOS, you would run the commandsudo yum instal...
你可以使用 ethtool 命令中的 -S 选项来查看网络使用情况统计。它可以显示传输的字节数、接收的字节数、错误数等。 # ethtool -S eth0 NIC statistics: Tx Queue#: 0 TSO pkts tx: 2053 TSO bytes tx: 7167572 ucast pkts tx: 4028081 ucast bytes tx: 399093197 mcast pkts tx: 0 mcast bytes tx: 0...
ethtool是用于查询及设置网卡参数的命令. 如果command not found可以用apt-get/yum添加。 主要参数: ethtool ethX//查看ethX设备属性 ethtool -h //显示帮助信息 ethtool -p|--identity ethX //识别网卡(使网卡的指示灯闪烁),主机有多个网卡时用处较大 ethtool -i|--driver ethX //显示网卡驱动的信息,如驱...
ethtool mlx5_2 ifconfig 查看所有网络 ethtool 查看网卡信息(带宽) nginx factory 和 用户中心 循环配置,导致接口一直404. -- 原因:一直在循环查找,杜绝环。 arping -I team0 10.30.115.107 获取ip的mac地址 ip route 路由表追踪 ip route|grep '192.168.111.' 查看网段追踪 查看网卡信息 ...
ifconfig eth0 up//启动网卡 ifconfig eth0 arp#开启arp协议ifconfig eth0 -arp#关闭arp协议ifconfig eth0 mtu1500#设置最大传输单元 ethtool 参考: https://www.cnblogs.com/danxi/p/6591885.html ethtool eth0 //查询ethx网口基本设置,其中 x 是对应网卡的编号,如eth0、eth1等等 ...
1. ifconfig: 使用ifconfig命令可以查看和配置网络接口。要停用当前网卡,可以使用ifconfig命令将其禁用。执行命令`ifconfig eth0 down`即可停用名为eth0的网卡。 2. ip command: ip命令是Linux网络配置的新工具,可以用来管理网络接口。要停用当前网卡,可以使用ip命令将其停用。执行命令`ip link set eth0 down`即...
mii-tool eth0 show link status of ‘eth0’ ethtool eth0 show statistics of network card ‘eth0’ netstat -tup show all active network connections and their PID netstat -tupl show all network services listening on the system and their PID tcpdump tcp port 80 show all HTTP traffic iwlist...
ethtool是一个用于查看和修改以太网接口驱动程序的工具。可以使用ethtool命令来检查和配置网卡的速度、双工模式、流控等参数。 例如:ethtool eth0 这些命令只是Linux中配置网络接口的一部分方法,根据具体情况和不同Linux发行版可能会有所差异。在使用这些命令进行网络接口配置时,建议先备份原始配置文件,以免配置错误导致网...
NVIDIA recommends using thel1-showcommand to monitor Ethernet data; refer toTroubleshoot Layer 1. Monitor Interface Status To check the status of an interface, run theethtool <interface>command: cumulus@switch:~$ ethtool swp1 Sett...