Linux Commandethtool 显示或修改以太网卡的配置信息 补充说明 ethtool命令用于获取以太网卡的配置信息,或者修改这些配置。这个命令比较复杂,功能特别多。 语法 ethtool [ -a | -c | -g | -i | -d | -k | -r | -S |] ethX ethtool [-A] ethX [autoneg on|off] [rx on|off] [tx on|off] ...
In most Linux distributions, the ‘ethtool’ command comes pre-installed. However, if it’s not, you can install it in Debian based distributions like Ubuntu, by running the commandsudo apt-get install ethtool. For RPM-based distributions like CentOS, you would run the commandsudo yum instal...
Examples: sed '2p' /etc/passwd 打印文件内容,并重复打印文件第2行 sed -n '2p' /etc/passwd 只打印文件第2行 sed -n '1,4p' /etc/passwd 只打印文件第1到4行 sed -n '/root/p' /etc/passwd 只打印文件匹配 root 的行 sed -n '2,/root/p' /etc/passwd 只打印文件从第2行开始到匹配 root...
ethtool mlx5_2 ifconfig 查看所有网络 ethtool 查看网卡信息(带宽) nginx factory 和 用户中心 循环配置,导致接口一直404. -- 原因:一直在循环查找,杜绝环。 arping -I team0 10.30.115.107 获取ip的mac地址 ip route 路由表追踪 ip route|grep '192.168.111.' 查看网段追踪 查看网卡信息 ...
which [-a] COMMAND -a:列出所有COMMAND命令。 文件内容查看 cat 正向显示全部内容。 cat [-AbEnTv] FILENAME[ ...]|STDIN -A:相当于-vET。 -b:显示行号,仅针对非空白行。 -E:将换行符显示为$。 -n:显示行号,包括空白行。 -T:将Tab显示为^I。
概要:ethtool ethX //查询ethX网口基本设置ethtool –h //显示et... 与时俱进 0 2549 Linux命令——ethtool 2018-12-13 21:04 − 参考:9 Linux ethtool Examples to Manipulate Ethernet Card (NIC Card) Fun with ethtool 简介 ethtool允许你修改Ethernet adapter配置,并且这种修改只适用于physical ...
instance[link_watch_0]:name:ethtool link:up down count:0runner:active port:ens160 4.6 .2手工配置lacp (此模式下上连交换机也要配置端口聚合) nmcli connection add type team con-name tema1 ifname team1 team.runner lacp192.168.10.21/24ipv4.method man ...
slave2 ifname em2 master Team1 man teamd.conf { "device": "team0", "runner": {"name": "activebackup"}, "link_watch": { "name": "ethtool", "delay_up": 2500, "delay_down": 1000 }, "ports": { "eth1": { "prio": -10, "sticky": true }, "eth2": { "prio": 100 ...
ethtool command ftp command host command ifstat command ip addr command iptables command iftop command ifup/ifdown command iwconfig command netstat command nload command nmap command nslookup command ping command route command scp command sftp command ...
10. ETHTOOL Command ethtoolis a replacement ofmii-tool. It is to view, setting speed and duplex of yourNetwork Interface Card(NIC). You can set duplex permanently in/etc/sysconfig/network-scripts/ifcfg-eth0withETHTOOL_OPTSvariable.