PRINT_START BED=[first_layer_bed_temperature] HOTEND={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} 添加以下code到printer.cfg [gcode_macro PRINT_START] gcode: #等待机器升温至第一层打印温度 M117 Heating... # Parameters {% set bedtemp = params.BED|int ...
结束打印时调用 M300 播放提示音,示例来自 CHEP###[gcode_macro START_PRINT] gcode: # chirp to indicate starting to print M300 S1000 P500 # Use absolute coordinates G90 # Reset
为了有效,网必须在开始打印之前召回。为此,可以在开始g代码的末尾、直接在切片器中或在START_PRINT宏中添加几行代码。以下是它在实践中的表现: BED_MESH_PROFILE LOAD=<name> 这将从匹配所提供名称的概要文件中恢复网格状态。这是激活补偿所必需的。 BED_MESH_PROFILE REMOVE=<name> 这样可以在g代码的末尾使用删除...
我注释掉的部分里面有PAUSE代码,运行之后并不会正确的PAUSE,暂停的位置跟我设置的不一样,而且恢复之后也不能正确打印。但我注释之后,把代码加在切片软件之后,不再由PRINT_START的宏调用就不会出现这种错误。 在切片软件里面配置起始Gcode 有时候Klipper出现问题真的是莫名其妙的......
sudo service klipper start 番外: 行空板板载一颗 MCU 控制大量引脚和传感器,本来想在其上面烧录 Klipper 固件,查阅型号为 GD32VF103C8T6,V代表 RISC-V 架构,这下懵了,目前 Klipper 最多只支持 OpenRISC 的 AR100 (全志的协处理器),还不支持此芯片,看来只能另辟蹊径了。这么说 LattePanda 是一个不错的 ...
鲁班猫只能通过SD卡来运行系统,我们根据教程将镜像烧录到SD卡:https://doc.embedfire.com/linux/rk356x/quick_start/zh/latest/quick_start/flash_img/flash_img.html#sd 烧录的镜像是Ubuntu20.04的镜像,考虑到后面可能会加MIPI屏幕,所以刷了xfce桌面版。这里要注意,由于打印机基本上是24小时运行的,所以SD卡要用...
(190)|float %} # Start bed heating M140 S{BED_TEMP} # Use absolute coordinates G90 # Zero the extruded length G92 E0 # Reset the G-Code Z offset (adjust Z offset if needed) SET_GCODE_OFFSET Z=0.0 # Home the printer G28 # Move the nozzle to the front G1 X60 Y0 F3000 # ...
Print intro line Start printing... I don't get any reasons, but if you still need to adjust the offset from your Slicers start GCode, then add this to yourPRINT_STARTmacroafterthe Z calibration: # Adjust the G-Code Z offset if needed ...
Does exactly the same as SDCARD_PRINT_FILE, but it just loads the file but then doesn't try to do_resume (print it) after. I refactored that part a bit. In the Artillery code, they literally copy&pasted SDCARD_PRINT_FILE and commented out the self.do_resume() at the end. They ...
Update the slicer start g-code. The START_PRINT macro has been updated/improved: uses your actual bed temperature for meshing etc., does a QGL with home Z, and does a Z_OFFSET_CALIBRATION before each print. Go to OrcaSlicer and edit the printer settings : ...