借助调平器调节热床调平螺丝,使喷嘴距离四颗热床螺丝上方的高度一致(SCREWS_TILT_CALCULATE)。也可以通过 A4 纸或肉眼观察,但主观性大,如想获得更好的首层效果,此类方法应弃用。 校准后的热床螺丝上方探测点可用于后续自动校正龙门倾斜(即双 Z 等高,Z_TILT_ADJUST) 【图 1】初次组装完成后,如未经校准,可能...
通过ssh连接鲁班猫,执行以下命令。 # 进入配置文件所在目录cd~/printer_data/config# 下载klicky-probe.cfg需要的宏命令wget https://raw.githubusercontent.com/jlas1/Klicky-Probe/main/Klipper_macros/Klipper_macros.zip# 解压unzip Klipper_macros.zip# 解压以后新增的文件klicky-probe.cfg#选择要开启功能的配置...
screws_tilt_adjust: initialize status result as a dictionary 11天前 lib lib: Update can2040 to v1.7.0 1个月前 scripts ci-install: Run 'apt-get update' prior to 'apt-get install' 2个月前 src Kconfig: Simplify WANT_XXX definitions 2个月前 test config: Config for Geee...
screws_tilt_adjust The following information is available in the screws_tilt_adjust object: error: Returns True if the most recent SCREWS_TILT_CALCULATE command included the MAX_DEVIATION parameter and any of the probed screw points exceeded the specified MAX_DEVIATION. max_deviation: Return...
I had to add 27mm to the X on each of the coordinates in [screws_tilt_adjust] for my probe to be over the bed screw. But shouldn't this already be done by the probe offset so when I press "Screw Adjust", which seems to run SCREWS_TILT_CALCULATE. The probe already knows to ...
五一假期的第一天,无所事事,还是折腾一下3D打印机吧,为我的Voron2.4换上鲁班猫做大脑。年前换配色拆了重装了一次,线基本已经走好了,不过现在只是能动起来的程度,还没好好调机。 先来看一下原来的布局和走线 现在我们的目标是把树莓派换成鲁班猫0,开干吧!!!(没有打标签的机器,手打标签,很难看有没有,还...
借助调平器调节热床调平螺丝,使喷嘴距离四颗热床螺丝上方的高度一致(SCREWS_TILT_CALCULATE)。也可以通过 A4 纸或肉眼观察,但主观性大,如想获得更好的首层效果,此类方法应弃用。 校准后的热床螺丝上方探测点可用于后续自动校正龙门倾斜(即双 Z 等高,Z_TILT_ADJUST) ...
screws_tilt_adjust: Add MAX_DEVIATION parameter for bed level invariant. 4年前 .gitignore util: Fix versioning when gitdir is absent (#809) 6年前 COPYING Initial commit of source code. 9年前 Makefile Makefile: Improve build when changing micro-controller architecture ...
五一假期的第一天,无所事事,还是折腾一下3D打印机吧,为我的Voron2.4换上鲁班猫做大脑。年前换配色拆了重装了一次,线基本已经走好了,不过现在只是能动起来的程度,还没好好调机。 先来看一下原来的布局和走线 现在我们的目标是把树莓派换成鲁班猫0,开干吧!!!(没有打标签的机器,手打标签,很难看有没有,还...
rotary_delta_calibrate.test screws_tilt_adjust.cfg screws_tilt_adjust.test sdcard_loop.cfg sdcard_loop.test temperature.cfg temperature.test tmc.cfg tmc.test z_tilt.cfg z_tilt.test z_virtual_endstop.cfg z_virtual_endstop.test .gitignore COPYING Makefile README.mdBreadcrumbs...