interpolate: True run_current: 0.9 hold_current: 0.7 sense_resistor: 0.110 stealthchop_threshold: 200 ### Z2轴设置 ### [stepper_z2] #Z2电机脉冲引脚设置 step_pin: PD5 #Z2电机方向引脚设置,可以通过添或删除引脚前面的!来改变电机的运转方向 dir_pin: !PD6 #Z2电机使能引脚设置 enable_pin: ...
# run_current: 0.8 # interpolate: True # stealthchop_threshold: 0 # [tmc2208 stepper_y] # uart_pin: PC13 # run_current: 0.8 # interpolate: True # stealthchop_threshold: 0 # [tmc2208 stepper_z] # uart_pin: PC7 # run_current: 0.8 # hold_current: 1.0 # interpolate: True # stealth...
[tmc2209 stepper_x]uart_pin: PE7run_current: 0.800hold_current: 0.500stealthchop_threshold: 0--- 这个位置---interpolate: Truedriver_sgthrs: 30diag_pin: PB14 [stepper_y]step_pin: PD8dir_pin: !PB12enable_pin: !PD9microsteps: 32rotation_distance: 40full_steps_per_rotation: 200endstop_...
run_current:0.9hold_current:0.7sense_resistor:0.110stealthchop_threshold:200###Z1轴设置###[stepper_z1]#Z1电机脉冲引脚设置step_pin: PE6#Z1电机方向引脚设置,可以通过添或删除引脚前面的!来改变电机的运转方向dir_pin: PC13#Z1电机使能引脚设置enable_pin: !PE5#---Klipper0.9以上版本设置---#电机...
run_current: 0.8 hold_current: 0.6 stealthchop_threshold: 999999 [tmc2209 stepper_z] uart_pin: gpio3 tx_pin: gpio4 uart_address: 3 run_current: 0.8 hold_current: 0.6 stealthchop_threshold: 999999 别外新增一个5轴全轴单线UART板子,已打板验证支持TMC2225 TMC2208的UART ...
RUN_SHELL_COMMAND CMD=voice_notify PARAMS={params.INFO} {% endif %} _EOF_ 测试及使用方法: 目前KlipperPad 内置支持打印开始、打印结束、检测到断料三个语音,位于~/Music文件夹内,分别对应数字 0-1-2 ,后续可根据需求增加。 启用语音播报:在printer.cfg文件中增加一句:[include misc/voice_notify.cfg]即...
run_current = 1.000 sense_resistor = 0.051 idle_current_percent = 20 [stepper_y] step_pin = PD7 dir_pin = !PD12 enable_pin = !PC6 step_distance = .0125 endstop_pin = ^PA2 position_endstop = 0 position_max = 210 [tmc2660 stepper_y] ...
Do not run data lines (USB, UART, CANBUS) close to and in parallel to high current lines like heaters or steppers. Use high quality cables (shielded / ferrite core). Keep such cables as short as possible | 避免通讯数据线(USB、UART、CANBUS)与高电流电源线(加热器、步进电机)太近或者并排...
run_current: The currently set run current. hold_current: The currently set hold current. toolhead The following information is available in the toolhead object (this object is always available): position: The last commanded position of the toolhead relative to the coordinate system specif...
run_current: 2.00 sense_resistor: 0.051 idle_current_percent: 20 #___ ON DRIVE Y ___ [stepper_y] step_pin: PD7 dir_pin: !PD12 enable_pin: !PC6 microsteps: 16 rotation_distance: 32 full_steps_per_rotation: 200 endstop_pin: ^PA2 ...