M83 ; restore position {% if printer[printer.toolhead.extruder].temperature >= printer.configfile.settings.extruder.min_extrude_temp %} G1 Z{zhop * -1} E{e} F900 ; prime nozzle by E, lower Z back down {% else %} G1 Z{zhop * -1} F900 ; lower Z back down without priming...
# The default is 0.100 seconds. #min_extrude_temp: 170 # The minimum temperature (in Celsius) at which extruder move # commands may be issued. The default is 170 Celsius. min_temp:0 max_temp:400 # The maximum range of valid temperatures (in Celsius) that the # heater must remain with...
max_temp: 270 # 挤出头传感器类型及Pin脚(TE0) sensor_type: NTC 100K MGB18-104F39050L32 sensor_pin: PC0 # 喷嘴直径 nozzle_diameter: 0.400 # 加热棒PWM最大输出功率 max_power: 1.0 # 加热棒最低挤出温度(达到此温度挤出机才能有挤出动作) min_extrude_temp: 170 # pid控制参数 control = pid p...
max_extrude_only_distance: 800.0 #control = pid #pid_kp = 16.644 #pid_ki = 1.099 #pid_kd = 63.038 [heater_bed] heater_pin: PG5 sensor_type: PT100 INA826 sensor_pin: PK2 min_temp: 0 max_temp: 100 #control = pid #pid_kp = 69.421 #pid_ki = 1.143 #pid_kd = 1054.331 [fan]...
sensor_pin: PC0# 喷嘴直径nozzle_diameter:0.400# 加热棒PWM最大输出功率max_power:1.0# 加热棒最低挤出温度(达到此温度挤出机才能有挤出动作)min_extrude_temp:170# pid控制参数control = pid pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 ...
can_extrude: If extruder can extrude (defined by min_extrude_temp), available only for extruder heaters The following information is available in the heaters object (this object is available if any heater is defined): available_heaters: Returns a list of all currently available heaters by...
Usage of [extruder].min_extrude_temp Why have we decided to use a dedicated repo? There are 2 main reasons for that decision The current moonraker changes have shown that we need to react very fast on changes. We regularly improve the macros and that is the simplest way that the installed...
min_temp: 0 max_temp: 250 #pressure_advance = 0.010 #max_extrude_only_distance: 150.0 [tmc2660 extruder] cs_pin: PC17 spi_bus: usart1 interpolate: True run_current: 1.0 sense_resistor: 0.051 #[multi_pin hevacs] #pins: sx1509_duex:PIN_15, sx1509_duex:PIN_4 #Fan7&8 ...
min_extrude_temp: 170 control = pid pid_kp = 26.213 pid_ki = 1.304 pid_kd = 131.721 ## Try to keep pressure_advance below 1.0 pressure_advance: 0.05 ## Default is 0.040, leave stock pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make sure to update be...
"bed_mesh": ["profile_name", "mesh_max", "mesh_min", "probed_matrix", "profiles"], "configfile": ["config"], "display_status": ["progress", "message"], "fan": ["speed"], "gcode_move": ["extrude_factor", "gcode_position", "homing_origin", "speed_factor", "speed"...