PRINT_START BED=[first_layer_bed_temperature] HOTEND={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} 添加以下code到printer.cfg [gcode_macro PRINT_START] gcode: #等待机器升温至第一层打印温度 M117 Heating... # Parameters {% set bedtemp = params.BED|int ...
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(190)|float %} # Start bed heating M140 S{BED_TEMP} # Use absolute coordinates G90 # Zero the extruded length G92 E0 # Reset the G-Code Z offset (adjust Z offset if needed) SET_GCODE_OFFSET Z=0.0 # Home the printer G28 # Move...
pid_Kd: 114 min_temp: 0 max_temp: 210 # Script to change back to the main extruder [gcode_macro T0] gcode: SET_SERVO SERVO=extruder_servo angle=100 # Lift secondary extruder SET_GCODE_OFFSET Z=0 MOVE=1 # Adjust z-height SET_GCODE_OFFSET X=0 # Clear X offset ACTIVATE_EXTRUDER EXT...
# 加热棒最低挤出温度(达到此温度挤出机才能有挤出动作) min_extrude_temp: 170 # pid控制参数 control = pid pid_kp = 26.213 pid_ki = 1.304 pid_kd = 131.721 pressure_advance: 0.05 pressure_advance_smooth_time: 0.040 [tmc2208 extruder] uart_pin: PA15 #microsteps: 16 interpolate: True run_c...
(默认:1.0)max_power:1.0kick_start_time:0.5heater: extruder#喉管散热风扇启动阀值heater_temp:50.0## If you are experiencing back flow, you can reduce fan_speedfan_speed:1.0shutdown_speed:1.0###打印冷却风扇(FAN1)###[fan]#模型冷却风扇引脚设置(FAN1)pin: PB2 kick_start_time:0.75#模型散热...
can_extrude: If extruder can extrude (defined by min_extrude_temp), available only for extruder heaters The following information is available in the heaters object (this object is available if any heater is defined): available_heaters: Returns a list of all currently available heaters by...
At it's simplest you need for each extruder tool to specify extruder, fan, offset to first tool or probe. Then specify four macros: pickup, dropoff, toollock and toolunlock. It doesn't matter if you lock the tool by a servo, a stepper or moving in a special way as long as it ...
-9.5:1 High Extruder Ratio-100Mbps Ethernet interface-500mm/s High-Speed Printing-Klipper Firmware Automatic Leveling Support online storage of automatic leveling offset data 9.5:1 High Extrusion Ratio All-Aluminum Extruder with a 5015 high rotation speed large air blower,can provide better heat ...
Fan1 controlled by extruder [heater_fan nozzle_cooling_fan] pin: PC26 heater: extruder heater_temp: 45 fan_speed: 1.0 ### ### BED ### ### #[heater_
heater: extruder heater_temp: 50.0 ## If you are experiencing back flow, you can reduce fan_speed #fan_speed: 1.0 [fan] ## Print Cooling Fan - FAN1 Connector pin: PB1 # Spider v1.x #pin: PA14 # Spider v2.x max_power: 0.4 kick_start_time: 0.5 ## Depending on...