G91 ; relative extruder positioning M83 ; restore position {% if printer[printer.toolhead.extruder].temperature >= printer.configfile.settings.extruder.min_extrude_temp %} G1 Z{zhop * -1} E{e} F900 ; prime nozzle by E, lower Z back down {% else %} G1 Z{zhop * -1} F900 ...
#min_extrude_temp: 170 # The minimum temperature (in Celsius) at which extruder move # commands may be issued. The default is 170 Celsius. min_temp:0 max_temp:400 # The maximum range of valid temperatures (in Celsius) that the # heater must remain within. This controls a safety feature...
[extruder] step_pin: PL7 dir_pin: PL6 enable_pin: !PC0 microsteps: 16 # 382.165 full_steps_per_rotation: 200 gear_ratio: 50:17 rotation_distance: 23.132 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PE4 sensor_type: PT100 INA826 sensor_pin: PK0 min_temp: 0 max_temp...
min_extrude_temp: 170 # pid控制参数 control = pid pid_kp = 26.213 pid_ki = 1.304 pid_kd = 131.721 pressure_advance: 0.05 pressure_advance_smooth_time: 0.040 [tmc2208 extruder] uart_pin: PA15 #microsteps: 16 interpolate: True run_current: 0.6 hold_current: 0.4 sense_resistor: 0.110 st...
min_temp: 0 max_temp:100 [multi_pin domofan] #多引脚同时控制多个风扇 pins: PB2,PA14,PA13 [fan] #模型散热风扇 ## Print Cooling Fan - FAN1 Connector #pin: PA14 # Spider v2.x pin: sht36v2:PB10 #sht36 can max_power: 1
(默认:1.0)max_power:1.0kick_start_time:0.5heater: extruder#喉管散热风扇启动阀值heater_temp:50.0## If you are experiencing back flow, you can reduce fan_speedfan_speed:1.0shutdown_speed:1.0###打印冷却风扇(FAN1)###[fan]#模型冷却风扇引脚设置(FAN1)pin: PB2 kick_start_time:0.75#模型散热...
can_extrude: If extruder can extrude (defined by min_extrude_temp), available only for extruder heaters The following information is available in the heaters object (this object is available if any heater is defined): available_heaters: Returns a list of all currently available heaters by...
Search or jump to... Search code, repositories, users, issues, pull requests... Provide feedback We read every piece of feedback, and take your input very seriously. Include my email address so I can be contacted Cancel Submit feedback Saved searches Use saved searches to f...
min_temp: 0 max_temp: 250 #pressure_advance = 0.010 #max_extrude_only_distance: 150.0 [tmc2660 extruder] cs_pin: PC17 spi_bus: usart1 interpolate: True run_current: 1.0 sense_resistor: 0.051 #[multi_pin hevacs] #pins: sx1509_duex:PIN_15, sx1509_duex:PIN_4 #Fan7&8 ...
max_temp: 250 [heater_bed] heater_pin: PB13 sensor_type: ATC Semitec 104GT-2 sensor_pin: PB1 control: pid pid_Kp: 54.027 pid_Ki: 0.770 pid_Kd: 948.182 min_temp: 0 max_temp: 130 [fan] pin: PA9 [heater_fan hotend_fan]