instantaneous_corner_velocity: 10.000 #两次挤出之间最大的速度变化(以毫米每秒为单位) max_extrude_only_distance: 100.0# 一次挤出或回抽的最大长度(以毫米耗材的长度为单位) max_extrude_only_velocity:5000# 最大的挤出和回抽速度(以毫米每秒为单位) max_extrude_only_accel:2000# 和加速度(以毫米每二次方...
#min_extrude_temp: 170 # The minimum temperature (in Celsius) at which extruder move # commands may be issued. The default is 170 Celsius. min_temp:0 max_temp:400 # The maximum range of valid temperatures (in Celsius) that the # heater must remain within. This controls a safety feature...
This value must be between min_temp and min_temp, inclusive. MINIMUM (default: min_temp) - A non-zero target temperature is clamped to no less than MINIMUM. This value must be between min_temp and min_temp, inclusive. TARGET (optional) - This specifies a new target temperature, ...
{% if TARGET < printer.configfile.settings[EXTRUDER].min_extrude_temp %} { action_raise_error("Extrude below minimum temp") } {% elifprinter.idle_timeout.state=="Printing"and not printer.pause_resume.is_paused %} { action_raise_error("Command not valid during printing.") } ...
max_temp: 250 #pressure_advance = 0.010 #max_extrude_only_distance: 150.0 [tmc2660 extruder] cs_pin: PC17 spi_bus: usart1 interpolate: True run_current: 1.0 sense_resistor: 0.051 #[multi_pin hevacs] #pins: sx1509_duex:PIN_15, sx1509_duex:PIN_4 #Fan7&8 ...
{ action_raise_error("Extrude below minimum temp.") } {% elif printer.idle_timeout.state == "Printing" and is_printing and not printer.pause_resume.is_paused %} { action_raise_error("Command not valid during printing.") } {% endif %} @@ -26,8 +30,8 @@ gcode: {% if EXTRUDER...
Set extrude factor override percentage: M221 S<percent> Set acceleration: M204 S<value> OR M204 P<value> T<value> Note: If S is not specified and both P and T are specified, then the acceleration is set to the minimum of P and T. If only one of P or T is specified, the ...
max_temp: 240 #最大温度 max_power:0.7 #最大功率 min_extrude_temp: 60 control = pid #PID_CALIBRATE HEATER=extruder TARGET=170 pid_kp = 14.488#先将模型冷却风扇设置为25%的转速( M106 S64 ),然后发送命令PID_CALIBRATE HEATER=extruder TARGET=245 它将执行一个PID校准程序,将持续约5分钟,完成后控...
MINIMUM(default:min_extrude_temp+ 5)- Ensures the extruder is heated to at least the specified temperature. Marlin Compatibility TheM701andM702commands are implemented with a default filament length ofvariable_load_length. Heaters Adds scaling parameters that can alter the behavior of the specified...
max_temp: 240 #最大温度 max_power:0.7 #最大功率 min_extrude_temp: 60 control = pid #PID_CALIBRATE HEATER=extruder TARGET=170 pid_kp = 14.488#先将模型冷却风扇设置为25%的转速( M106 S64 ),然后发送命令PID_CALIBRATE HEATER=extruder TARGET=245 它将执行一个PID校准程序,将持续约5分钟,完成后控...