设置虚拟限位 也就是endstop_pin: tmc2209_stepper_x: virtual_endstop这个位置 设置灵敏度 对于灵敏度的设置需要根据你自己的机器做调整数值在driver_sgthrs设置,对于TMC2209,数值可以在0到255之间浮动,越高越灵敏,这个值需要自己测试 需要归零速度稍微快一点,比如50,不要用10的速度,太慢不符合无限位归零的触发...
(默认已设置,无需改动)设置homing_retract_dist: 0 (默认已设置,无需改动)设置对应电机endstop_pin: tmc2209_stepper_x:virtual_endstop (无需设置,如果非2209/2240,则改为-63)设置driver_SGTHRS: 255 (默认已设置,无需改动)设置正确的diag_pin override.cfg 内容# Copy # [include override.cfg][idle_ti...
# 限位开关PIN脚设置(Y-) endstop_pin: ^PB13 [tmc2208 stepper_y] uart_pin: PE15 #microsteps: 16 interpolate: True run_current: 0.9 hold_current: 0.7 sense_resistor: 0.110 stealthchop_threshold: 200 ### E0挤出机设置 ### [extruder] # 挤出机电机脉冲引脚设置 step_pin: PD12 # 挤出机电...
来改变电机方向enable_pin:!MOT0_ENmicrosteps:64# 推荐16细分以达到较好的精度和静音效果position_max:1000# step_pulse_duration: 0.000004rotation_distance:40# 同步轮周长mm(2GT-20T带轮40,2GT-16T带轮32)endstop_pin:^!ESTOP0# X_MINposition_endstop:0# X Offset,用于设置打印平台偏移[stepper_y]...
enable_pin: !PA5 microsteps: 16 rotation_distance: 40 endstop_pin: ^!PA0 position_endstop: 0 position_max: 223 homing_speed: 50.0 [stepper_y] step_pin: PC5 dir_pin: PC4 enable_pin: !PC6 microsteps: 16 rotation_distance: 40 ...
Good afternoon, I have finally got things another few steps and actually thru the config checks got the stepper motors to move. But they will not home at all. I am using a Bigtreetech SKR 1.3 board and had to take the 2130's out and go back on my Anycubic delta with the old chips...
软件限位(如果是350机型,需更改为350)position_max:300# X轴的机械复位点坐标(如果是350机型,需更改为350)position_endstop:300# 复位速度homing_speed:25# 第一次触发复位开关之后的后退距离homing_retract_dist:5# 复位方向(一般不需要改动)homing_positive_dir:true# 限位开关PIN脚设置(X-)endstop_pin: ^...
endstop_pin: probe:z_virtual_endstop position_max: 670 position_min: -0.5 [tmc2660 stepper_z] cs_pin: PD24 spi_bus: usart1 interpolate: True run_current: 1.800 sense_resistor: 0.051 idle_current_percent: 20 #___ Z1 ON DRIVE E4 ___ [stepper_z1] step_pin: PD0 dir_pin: !PD16...
enable_pin: !PB9 microsteps: 16 rotation_distance: 40 endstop_pin: ^PA3 position_endstop: 0 position_max: 235 homing_speed: 50 [stepper_y] step_pin: PB5 dir_pin: PB4 enable_pin: !PB9 microsteps: 16 rotation_distance: 40