pin: EXP1_1#无源蜂鸣器(piezo beeper)需要 PWM 信号控制,有源(DC buzzer)不需要pwm: True value: 0#Silent at power on,setto 1ifactive low.shutdown_value: 0#Disable at emergency shutdown (no PWM would be available anyway).cycle_time: 0.001#Default PWM frequency : 0.001 = 1ms will give a...
# btn.cfg## 自锁按钮[gcode_buttonfan_lock_switch]pin:PA2# UART2press_gcode:SET_FAN_SPEEDFAN=two_wire_fanSPEED=1.0release_gcode:SET_FAN_SPEEDFAN=two_wire_fanSPEED=0.0## 非自锁按钮# 如果是 output_pin 可以直接获取引脚状态每次取反,这里定义一个用于存储状态值以取反的宏,变量名不含大写字符[g...
# set slicer cura START_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0} # set orca START_PRINT BED_TEMP={S[first_layer_bed_temperature]} EXTRUDER_TEMP={S[first_layer_temperature]} gcode: {% set BED_TEMP = params.BED_TEMP|default(60)...
SET_GCODE_OFFSET Z=0.100 MOVE=1 # Adjust z-height SET_SERVO SERVO=extruder_servo angle=100 # Position second extruder SET_GCODE_OFFSET X=5 # Account for different X offset ACTIVATE_EXTRUDER EXTRUDER=extruder1 # Servo definition [servo extruder_servo] pin: ar7...
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=zhop VALUE=0 {% endif %} G1 E-{e} F2100 SAVE_GCODE_STATE NAME=PAUSEPARK G90 ; absolute positioning G1 X10 Y10 F6000 ; park toolhead at front center #M104 S0 ; turn off hotend SET_IDLE_TIMEOUT TIMEOUT=43200 ; set timeout to 12 hours ...
# set_position_z: 0 # gcode: # G90 # G0 Z10 F600 # G28 X Y # ## XY Location of the Z Endstop Switch # ## Update X0 and Y0 to your values (such as X157, Y305) after going through # ## Z Endstop Pin Location Definition step. ...
After Klipper reports that the printer is ready go on to the config check document to perform some basic checks on the pin definitions in the config file. note: do not forgot put the jumpers on the H4 to Klipper printing mode.
value: The "value" of the pin, as set by a SET_PIN command. quad_gantry_level The following information is available in the quad_gantry_level object (this object is available if quad_gantry_level is defined): applied: True if the gantry leveling process has been run and completed...
SET_PINPIN=beeperVALUE={S} G4 P{P} SET_PINPIN=beeperVALUE=0 {% else %} {action_respond_info( "M300 is disabled. To enable create an [output_pin beeper] config.")} {% endif %} 88 changes: 88 additions & 0 deletions88fans.cfg ...
(Debian 11 with Klipper), a 4K capable micro HDMI port, Fast Ethernet and WiFi 4 networking, four USB ports, and the usual 40-pin Raspberry Pi header. BTT Pi specifications: SoC – Allwinner H616 quad-core Arm Cortex-A53 @ 1.5GHz with Arm Mali G31 MP2 with support for OpenGL ES ...