以KLP1 厂家自带的 gcode 为例改造。 更改配置有风险,操作请谨慎 BED_MESH_PROFILE LOAD="default" ;;; 以下 gcode 是新加的 G28 ; h1ome all axes G91; relative positioning G1 Z3.0 F3000 ; move z up little to bake by bed temperature ;;; M104 S[nozzle_temperature_initial_layer] M190 S[...
[bed_mesh]## 热床网格校准speed:60# 校准速度horizontal_move_z:13# Z起始高度mesh_min:50,50# 最小校准点坐标x,ymesh_max:250,250# 最大坐标probe_count:15,15# 采样点数mesh_pps:2,2# 补充采样点数algorithm: bicubic# 算法模型bicubic_tension:0.2# 算法插值不要动relative_reference_index:112# 第...
[gcode_macro G32] gcode: BED_MESH_CLEAR G28 QUAD_GANTRY_LEVEL G28 G0 X150 Y150 Z20 F6000 [gcode_macro PRINT_START] # Use PRINT_START for the slicer starting script - please customise for your slicer of choice gcode: G32 ; home all axes G1 Z20 F3000 ; move nozzle away from be...
KlipperDelta配置文件,针脚适配于MKS BASE1.4主板 虚拟SD卡文件,GCODE文件路径适用于Mainsail控制面板 连杆长度,限位开关位置,打印范围之类的需要自己用塞纸法自动校准一下 [mcu]serial:/dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL00PU19-if00-port0# 连接到单片机的串行通讯接口# 如果你不确定的话(或可能...
All features are configured by setting variable_ values in the [gcode_macro _km_options] section. All available variables and their purpose are listed in globals.cfg. Note: PRINT_START specific customizations are covered in more detail below. Bed Mesh Improvements BED_MESH_CALIBRATE_FAST Wraps th...
[gcode_macro bed_mesh_calibrate_fast] description: Wraps BED_MESH_CALIBRATE, scaling probe count to specified area. Usage: See Klipper documentation. gcode: {% setkm= printer["gcode_macro _km_globals"] %} {% setprobe_mesh_padding= km.probe_mesh_padding %} ...
Have you ever read about something and thought, “Gee whiz! Why did I never think about that?” That was my reaction to reading about a feature commonly associated with Klipper calledadaptive bed levelingor adaptive mesh leveling. Too bad I don’t typically use Klipper, but it all worked ...
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice gcode: G32 ; home all axes G1 Z20 F3000 ; move nozzle away from bed [gcode_macro PRINT_END] # Use PRINT_END for the slicer ending script - please customise for your slicer of choice...
鲁班猫运行Linux系统,作为上位机,在系统中运行一些与3D打印控制相关的服务,如解算模型Gcode代码,振动补偿,压力补偿、温度调节等计算,同时提供web service接口,可以相关接口来对3D打印机的参数和状态进行设置和监控。还提供显示接口,通过接入的屏幕来直接设置打印参数。
# gcode: # BED_MESH_CLEAR #清除调平数据 # G28 # BED_MESH_CALIBRATE #自动调平 # BED_MESH_PROFILE SAVE="name" #保存调平数据 # SAVE_CONFIG # BED_MESH_PROFILE LOAD="name" #加载调平数据 # [gcode_macro G31] # gcode: # TESTZ Z=-1 ...