set routing-options static route 0.0.0.0/0 next-hop 10.1.1.1 /***配置逻辑接口地址及缺省路由,SRX接口要求IP地址必须配置在逻辑接口下(类似ScreenOS的子接口),通常使用逻辑接口0即可***/ set security zones security-zone untrust interfaces ge-0/0/0.0 /***将ge-0/0/0.0接口放到untrust zone去,类似Sc...
static-options--(Optional under route) Additional information about static routes, which is included with the route when it is installed in the routing table. You can specify one or more of the following in static-options. Each of the options is explained separately. * (active | passive); *...
Juniper-R&S-BGP(2):IBGP的初始配置+宣告BGP路由条目 1、进入Routing-options 指定AS号码 命令: set routing-options autonomous-system xxxxx ---注明:BGP私有AS号64512-65535 2、进入BGP协议的层级,手工配置邻居 root# edit protocols bgp group ibgp---进入BGP协议的层级 [edit protocols bgp group ibgp] root...
# 配置接口描述、配置IP地址。 set routing-options static route 0.0.0.0/0 next-hop 1.1.1.2 # 配置默认路由指向公网出口网关。 show route inet.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 0.0.0.0/0 *[Static/5] 00:00:33...
⑴ `set routing-options static route destination next-hop`:配置静态路由。 ⑵ `set protocols ospf area area-id`:配置OSPF路由协议。 ⒋ 安全配置命令 ⑴ `set security zones security-zone zone-name interfaces interface-name`:将接口分配给安全区域。 ⑵ `set security policies from-zone source-zone to...
所以的配置在routing-options 级别 Syntax: [edit] routing-options { static { defaults { static-options; } route destination-prefix { next-hop next-hop; qualified-next-hop address { metric metric; preference preference; } static-options;
set policy-options policy-statement no-for-a term 1 then reject routing-options forwarding-table export 检查FIB表: Routing table: A.inet Internet: Destination Type RtRef Next hop Type Index NhRef Netif default perm 0 rjct 526 1 0.0.0.0/32 perm 0 dscd 524 1 ...
set routing-options autonomous-system 64515 router-id配置: set routing-options router-id 1.1.1.1 静态路由 set routing-options static route 0.0.0.0/0 next-hop 10.0.0.2 set routing-options static route 100.0.0.0/24 next-hop 12.12.12.2 resolve(juniper设备默认不进行递归查找,如果需要递归则在后面加上...
routing-options : 配置静态路由或router-id 等系统全局路由属性配置。二、SRX®火墙配置对照说明策略处理流程图初始安装登陆Console 口(通用超级终端缺省配置 )连接SRX, root 用户登陆,密码为空login: rootPassword:- JUNO 7、S built 2009-07-16 15:04:30 UTCroot% cli/ / 进入操作模式root>root> configure...
9、射"(2)对于isp2出口 :采用静态路由协议,指定访问某些目的地址路 由走bbbb出口 ;对内网使用了 isp2 internet ip的用户采用静 态策略路由将流量指向isp2出口;对内网特定的保留ip用户采用静态策略路由 走isp2出口,并进行pat地址转换以访问isp2出口 f厂juniper的相关设置 静态策略路由设置routing-options ?interface...