螺栓螺纹的根部半径 直径为MJ1,6至MJ5的螺母4H6H螺纹的极限尺寸、直径为MJ6至MJ39的螺母4H5H螺纹的限制尺寸 Maximum permissible deviations on pitch (lead) and on half flank angle 替代历史
AReference numberISO 5855-1:1999(E)INTERNATIONALSTANDARDISO5855-1Third edition1999-10-15Aerospace — MJ threads —Part 1:General requirementsAéronautique et espace — Filetage MJ —Partie 1: Exigences généralesCopyright International Organization for Standardization Provided by IHS under license with ...
摘要: 本文件仍处于研究中,更动在所难免,不应引用,仅供参考. 0.前言 MJ螺纹基本牙型与公制螺纹基本牙型(ISO68)的唯一差别是内螺纹内径D_1的削顶高度增大了(由0.2500H改为0.3125H).这是由于外螺纹内径d_3采用了0.18042P的最大圆角半径而要求的(见ISO/DIS 5855/II).关键词:...
Aerospace - MJ threads - Part 1: General requirements (ISO 5855-1:1999); Text in German and Englishdoi:DIN ISO 5855-1
内容提示: AReference numberISO 5855-1:1999(E)INTERNATIONALSTANDARDISO5855-1Third edition1999-10-15Aerospace — MJ threads —Part 1:General requirementsAéronautique et espace — Filetage MJ —Partie 1: Exigences générales ... 文档格式:PDF | 页数:41 | 浏览次数:80 | 上传日期:2017-03-14 ...
iso 5855 consists of the following parts, under the general title aerospace mj threads: part 1: general requirements part 2: limit dimensions for bolts and nuts part 3: limit dimensions for fittings for fluid systems international standard isoiso 5855-2:1999(e) 1 aerospace mj threads part 2:...
$R'4"1470417www.din.deDDIN ISO 5855-1Luft- und Raumfahrt –MJ-Gewinde –Text Deutsch und EnglischAerospace –MJ threads –Aéronautique et espace –Filetage MJ –Partie 1: Exigences générales (ISO 5855-1:1999); ©Alleinverkauf der Normen durch Beuth Verlag GmbH, 10772 BerlinErsatz für...
航空航天 MJ螺纹 第1部分:一般要求 Aerospace - MJ threads - Part 1: General requirements ISO 5855-1:1999 发布历史 ISO 5855-1:1999由国际标准化组织 IX-ISO 发布于 1999-10。 ISO 5855-1:1999 在中国标准分类中归属于: V04 基础标准与通用方法,在国际标准分类中归属于: 49.030.10 螺纹。
ISO 5855 的这一部分规定了用于航空航天结构的公称直径为 1.6 毫米至 39 毫米的螺栓和螺母的 MJ 螺纹的限制尺寸。 购买 正式版 其他标准 DIN ISO 5855-2:2009 航空航天.MJ螺纹.第2部分:螺栓,螺母极限尺寸(ISO 5855-2:1999),德文和英文版本 专题
ISO 5855 的这一部分规定了 MJ 螺纹的基本轮廓。该基本型材适用于航空航天结构中公称直径为 1.6 毫米及以上的所有螺纹零件。公称直径为 1 mm 和 1.2 mm 的螺纹部件应符合 ISO/R 1501 标准。This part of ISO 5855 specifies the basic profile