当用ip default-network指令设定多条默认路由时,administrative distance最短的成为最终的默认路由;如果有复数条路由distance值相等,那么在路由表(show ip route)中靠上的成为默认路由。 同时使用ip default-network和ip route 0.0.0.0 0.0.0.0双方设定默认路由时,如果ip default-network设定的网络是直连(静态、且已知)...
在 route 命令仅在主路由表(表 254)上运行的情况下,ip route 命令默认情况下在主路由表上运行,但可以通过 table 参数轻松coaxed into使用其他表。 D.2. ip route (linux-ip.net):http://linux-ip.net/html/tools-ip-route.html#tools-ip-route-show ip命令与ifconfig命令类似,但比ifconfig命令更加强大,...
route add –host 192.168.4.2 dev eth0:1 route add –host 192.168.4.1 gw 192.168.4.250 1. 2. 示例2:添加到网络的路由 route add –net IP netmask MASK eth0 route add –net IP netmask MASK gw IP route add –net IP/24 eth1 1. 2. 3. 示例3:添加默认网关 route add default gw IP 1....
ip route add default via <gateway_ip> dev <interface> 4.3 新增网卡地址 使用以下命令,给eth0网卡,新增ip地址。 ip addr add 192.168.1.100/24 dev eth0 查看新增的IP地址,注意新增的IP地址是临时生效,要长久生效,修改网卡配置文件或者使用nmcli命令。 ip add show 在这里插入图片描述 4.4 删除新增网卡...
route -n显示现在所有路由 root@Ubuntu:~# route 结果是自上而下, 就是说, 哪条在前面, 哪条就有优先, 前面都没有, 就用最后一条default, 1、第一行的意思就是去往所有目标地址数据包由网关192.168.124.1 通过网卡eth0来转发,Flags那一列中有G时才会使用Gateway ...
ROUTE [-f] [-p] [command [destination][MASK netmask] [gateway] [METRIC metric] [IF interface]-f Clears the routing tables of all gateway entries. If this isused in conjunction with one of the commands, the tables arecleared prior to running the command.-p When used with the ADD ...
route [-f] [-p] [Command [Destination] [mask Netmask] [Gateway] [metric Metric]] [if Interface]] 2.命令功能: route命令是用于操作基于内核ip路由表,它的主要作用是创建一个静态路由让指定一个主机或者一个网络通过一个网络接口,如eth0。当使用"add"或者"del"参数时,路由表被修改,如果没有参数,则显...
使用全局配置模式命令ipx default-route可使缺省路由起作用 两者存在一定关系的.比如这条 ip route 172.16.1.0 255.255.255.0 100 这条命令,简单解释就是去往172.16.1.0 255.255.255.0 这个网段 通过下一跳地址192.168.10.0 .当这个地址不在本网段的时候 那么,就得去寻找default-gateway了...
-f Clears the routing tables of all gateway entries. If this is used in conjunction with one of the commands, the tables are cleared prior to running the command. -p When used with the ADD command, makes a route persistent across
gateway=?" command to add a route to the target network segment. Run the "add port ipv6_route eth_port_id=? host gateway=?" command to add a route to the target application server. Run the "add port ipv6_route eth_port_id=? default gateway=?" command to add the default route. ...