ip default-network ip route 0.0.0.0 0.0.0.0 Use Command ip default-gateway Theip default-gatewaycommand differs from the other two commands as it must only be used when ip routing is disabled on the Cisco router. For instance, if the router is a host in the IP world, you can use this...
ip default-network、ip route、ip default-gateway的区别 在cisco的16448文档中详细地讲解了这三条命令的使用条件和区别。一、使用条件ip default-gateway在禁用了ip routing的情况下使用，该路由器被当做默认网关。ip default-network和ip route 0.0.0.0 0.0.0.0 则可以在启用路由选择协议下使用。二、区别ip ...
When does a Cisco router initiate a routing request out its interfaces? What is the difference between the ip default-gateway, ip default-network, and ip route 0.0.0.0/0 commands? How do I use the ip helper-address command to forward Bootstrap Protocol (BOOTP) frames?
Cisco 特殊VLAN划分之一个VLAN多个网段IP 1.拓扑如图所示. 2.连线示意如下: Switch1 F0/1 <---> Router1 F0/0 Switch1 F0/2 <---> Router2 F0/0 Switch1 F0/3 <---> Router3 F0/0 Switch1 F0/4 <---> Router4 F0/0 3.r01,r02,r03模拟PC。ip地址分别为:192.168.1.1;192.168.2.2;192.168...
Router (dhcp-config)#default-router 192.168.1.1 Router(dhcp-config)#dns-server 202.106.0.20 202.106.148.1 Router(dhcp-config)#lease 2 Router(config)#ip dhcp excluded-address 192.168.1.33 关于这段配置,下列说法正确的是( )。(选2项) A. 该网络中主机有可能自动获取192.168.1.50/24的IP地址 B. 该...
ip dhcp pool cisco network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 255.255.255.0 下面的pc获取测试dhcp配置正常。 2.设置PC获取指定的ip地址 用client-identifier这个命令就能实现这个功能,但是需要为DHCP客户端指定的唯一标识符,此命令用于DHCP请求。
The end result i found, ip default-network command does not have any influence in ospf except for one: when ip default-network is configured on local router and it references the ospf learned route whether subnetted or unsubnetted, it sets the default gateway on that router only. It does ...
default-router 192.168.1.1 dns-server 192.168.1.1 ip domain name multilink bundle-name authenticated 3. show version show version命令用于显示设备的硬件信息、软件版本、配置寄存器信息以及设备启动时间等信息。 Router# show version 返回示例: Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M...
route[-f][-p][Command [Destination][mask Netmask][Gateway][metric Metric]][if Interface]]1 -f清除所有网关入口的路由表。-p与add命令一起使用时使路由具有永久性。Command指定您想运行的命令 (Add/Change/Delete/Print)。Destination指定该路由的网络目标。mask Netmask指定与网络目标相关的网络掩码(也被称作...
The “show ip route”command is one of the most important commands related to routing on Cisco IOS devices in order to show the routing table of the router. It gives you detailed information about the networks that are known to the router, either directly connected to the router, statically...