launch 新的 instance “cirros-vm1”,网络选择 vlan100。 cirros-vm1 分配到的 IP 为 172.16.100.3。 cirros-vm1 被 schedule 到控制节点,对应的 tap 设备为 tapc1875c7f-cb,并且连接到 bridge。 当前vlan100 的结构如下。 继续用同样的方式 launch instance cirros-vm2,分配到的 IP 为 172.16.100.104。
<HUAWEI> system-view [HUAWEI] sysname DeviceB [DeviceB] interface Vlanif100 [DeviceB-Vlanif100] vrrp vrid 1 virtual-ip 10.1.1.10 [DeviceB-Vlanif100] quit After completing the configurations, run the display vrrp verbose command on DeviceA or DeviceB to view the VRRP status. The command...
点击“Create Network”,vxlan100 创建成功。 点击vxlan100 链接,进入 network 配置页面,目前还没有 subnet,点击 “Create Subnet” 按钮。 创建subnet_172_16_100_0,IP 地址为 172.16.100.0/24。 将instance 连接到 vxlan100_net launch 新的 instance “cirros-vm1”,“cirros-vm2” 网络选择 vxlan100。 cir...
bridge-domain vlan-id [access | dot1q [tag] | dot1q-tunnel] [broadcast] [ignore-bpdu-pid] [pvst-tlv CE-vlan] [increment] [lan-fcs] [split-horizon] no bridge-domain vlan-id Syntax Description vlan-id The number of the VLAN to be used in this bridging configuration. The valid...
debug sw-vlan vtp debug udld debug vqpc define interface-range deny diagnostic monitor action diagnostic start dot1x auth-fail max-attempts dot1x auth-fail vlan dot1x guest-vlan dot1x guest-vlan supplicant dot1x host-mode dot1x initialize dot1x max-reauth-req dot1x max-req dot1...
[SwitchC] erps ring 1 [SwitchC-erps-ring1] control-vlan 10 [SwitchC-erps-ring1] protected-instance 1 [SwitchC-erps-ring1] quit [SwitchC] stp region-configuration [SwitchC-mst-region] instance 1 vlan 10 100 to 200 [SwitchC-mst-region] active region-configuration [SwitchC-mst-region]...
#interface GigabitEthernet0/0/1port link-type accessport default vlan 100#return[C-SW]dis cu int gi0/0/2#interface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 10 20#return[C-SW]dis cu int vlan 10#interface Vlanif10...
Create ERPS ring 1 and ERPS ring 2 and configure ERP instances in the two rings. Set the control VLAN ID of ERPS ring 1 to 10 and the control VLAN ID of ERPS ring 2 to 20. Enable ERPS ring 1 to transmit data packets from VLANs 100 to 200 and enable ERPS ring 2 to transmit dat...
Create ERPS ring 1 and ERPS ring 2 and configure ERP instances in the two rings. Set the control VLAN ID of ERPS ring 1 to 10 and the control VLAN ID of ERPS ring 2 to 20. Enable ERPS ring 1 to transmit data packets from VLANs 100 to 200 and enable ERPS ring 2 to transmit dat...
launch 新的 instance “cirros-vm1”,网络选择 vlan100。 cirros-vm1 分配到的 IP 为 172.16.100.3。 cirros-vm1 被 schedule 到控制节点,其虚拟网卡也连接到 br-int。 虚拟网卡与 br-int 的连接方式与 local 和 flat 网络没有任何区别,不再赘述。