Pinctrlsubsystem 分为3部分:Pinctrl core、Pinmux和Pinconf。 pinctrlcore是pincontrol子系统的核心,提供了和devicedriver交互的API; pinmux用于实现pin的复用; pinconf用于实现pin的配置,如输入/输出、pulldown/pull up、driverstrength等;另外还提供了用于debug的接口。 与gpio子系统的交互 虽然pinctrl提供了pinctrl_re...
Does gpio_set_drive_capability have any effect if the pin is used by peripheral driver, like I2C or UART? Does this setting persist forever? I saw there's also gpio_reset_pin but there's no info it will reset driver strength. Regards, ChrisMicroController...
Driver 层接口设计 以下接口是 Pin 设备驱动框架的标准接口。 c struct rt_pin_ops { void (*pin_mode)(struct rt_device *device, rt_base_t pin, rt_base_t mode); void (*pin_write)(struct rt_device *device, rt_base_t pin, rt_base_t value); int (*pin_read)(struct rt_device ...
Now the drive strength (current source & sink capability) of GPIO pin is based on the value configured for DSE field of the register as shown in below picture: So from this, Q1: If DSE is 001 and VDD is 3.3V then the current I can source or sink ...
1.1.1.12.gpio_get_drive_strength 获取gpio输出强度等级,只支持单个io。 原型: // 获取单个io输出强度 pin:只能带入1个ioenumgpio_drive_strengthgpio_get_drive_strength(enumgpio_portport,u32pin); 参数: 1.1.1.13.gpio_hw_op_dir 1.1.1.14.gpio_hw_op_out ...
I think if the drive strength of the GPIO becomes higher, this issue will be solved. Q1 If I set SRE=1(fast slew rate), the waveform became worse. Please refer to the attached Case1 and Case2. Should I use slow slew rate when the frequency is high? Q2 If I use driver IC whose...
drive-strength = <2>; /* 2 MA */ bias-disable; /* No PULL */ }; }; 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 修改client node包含pinctrl states。删除隐形gpio参数,使用GPIO芯片节点。
Pinctrl sunxi driver:sunxi 平台需要实现的驱动。 Board configuration:设备 pin 配置信息,一般采用设备树进行配置。 2.4 state/pinmux/pinconfig Pinctrl framework 主要处理 pinstate、pinmux 和 pinconfig 三个功能,pinstate 和 pinmux、pinconfig 映射关系如下图所示。
Pinctrl sunxi driver:sunxi 平台需要实现的驱动。 Board configuration:设备 pin 配置信息,一般采用设备树进行配置。 2.4 state/pinmux/pinconfig Pinctrl framework 主要处理 pinstate、pinmux 和 pinconfig 三个功能,pinstate 和 pinmux、pinconfig 映射关系如下图所示。
gpio_init_struct.DrvStrength = GPIO_DRV_STRENGTH_HIGH;if(out_mode == BSP_GPIO_PIN_OUT_OD) { gpio_init_struct.Mode = GPIO_MODE_OUTPUT; gpio_init_struct.OpenDrain = GPIO_OPENDRAIN; }elseif(out_mode == BSP_GPIO_PIN_OUT_PP)