1、默认路由配置命令 FortiGate # config router static FortiGate (static) # edit 1 FortiGate (1) # set gateway 202.1.1.1 //本条目没有定义dst目的网络,则默认为为0.0.0.0/0.0.0.0 FortiGate (1) # set device wan1 FortiGate (1) # next 2、目的网段静态路由配置 FortiGate # config router static F...
FortiGate (port1) # set ip 192.168.8.99/24 FortiGate (port1) # end 2.配置静态路由 FortiGate (static) # edit 1 FortiGate (1) # set device wan1 FortiGate (1) # set dst 10.0.0.0 255.0.0.0 FortiGate (1) # set gateway 192.168.57.1 FortiGate (1) # end 3.配置默认路由 FortiGate (1) ...
exit Exit the CLI. 退出 二、常用命令 1.配置接口地址: FortiGate # config system interface FortiGate (interface) # edit lan FortiGate (lan) # set ip 192.168.100.99/24 FortiGate (lan) # end 2.配置静态路由 FortiGate (static) # edit 1 FortiGate (1) # set device wan1 FortiGate (1) # set...
1、配置接口地址:FortiGate # config system interface FortiGate (interface) # edit lan FortiGate (lan) # set ip 192.168.100.99/24 FortiGate (lan) # end 2、配置静态路由 FortiGate (static) # edit 1 FortiGate (1) # set device wan1 FortiGate (1) # set dst 10.0.0.0 255.0.0.0 ...
5、; 退出 二、常用命令 1、配置接口地址 : FortiGate # config system interface FortiGate (interface) # edit lan FortiGate (lan) # set ip 192 6、.168.100.99/24 FortiGate (lan) # end 2、配置静态路由 FortiGate (static) # edit 1 FortiGate (1) # set device wan1 FortiGate (1) # set dst...
公网IP:114.11.189.23 内网地址:10.20.29.0/24 共享密钥:zhongxingguoji 二、Hillstone基础网络配置: 设置公网接口: interface ethernet0/3 zone "untrust" ip address 114.11.189.23/27 description "To_Internet_wan" manage ping manage ssh manage https 设置内网接口: interface ethernet0/1 zone "trust" ip ad...
FortiGate (lan) # set ip 192.168.100.99/24 FortiGate (lan) # end 2、配置静态路由 FortiGate (static) # edit 1 FortiGate (1) # set device wan1 FortiGate (1) # set dst 10.0.0.0 255.0.0.0 FortiGate (1) # set gateway 192.168.57.1 FortiGate (1) # end 3、配置默认路由 FortiGate (1) ...
$$し-νρη门户配置页面,我们将隧道分割调整为“禁用”,使所有客户端流量都经过$$し-νρη隧道进行转发,源IP池保持使用$$し νρη隧道地址池。 还有一些其他配置,我们暂时保持默认即可。 然后进入到“νρη”下面的“$$し-νρη设置”,指定监听接口为WAN接口port1,将监听端口修改为9999(注意:公有云上...
mode: static ip: 88.2.192.52 255.255.255.240 status: up speed: 1000Mbps Duplex: Full show router static查看默认路由的配置 显示结果如下 config router static edit 1 set device "wan1" set gateway 27.151.120.X next end get router info routing-table static ...
FortiGate (lan) # set ip 192.168.100.99/24 FortiGate (lan) # end 2、配置静态路由 FortiGate (static) # edit 1 FortiGate (1) # set device wan1 FortiGate (1) # set dst 10.0.0.0 255.0.0.0 FortiGate (1) # set gateway 192.168.57.1 FortiGate (1) # end 3、配置默认路由 FortiGate (1) ...