MEMO Error Codes ( ID = 7 )MEMO-001WARN System error可能原因:系统内部错误。 解决方法:和我们当地的客服中心联系。MEMO-002WARN Specified program is in use可能原因:指定程序正在编辑或执行。解决方法:取消指定程序,或在选择其他程序后再选择一次该程序。MEMO-003WARN Specified program is in use可能原因:...
SRVO--057 SERVO2 FSSB disconnect (Group:%d Axis:%d) FANUC报警信息代码 可能原因:从SLAVE到SRVO间FSSB传输断开。 解决方法:检查FSSB硬件连接。 SRVO--058 SYSTEM FSSB init error (N:%d) 可能原因: 在初始化过程中,出现FSSB传输错误。 解决方法:检查FSSB硬件连接。 SRVO--059 SYSTEM Servo amp init error ...
If your machine is equipped with Fanuc Automation components, and your CNC machine suddenly stops working, you probably check the status display on your Fanuc servo amplifier to see what number is displayed. These numbers are error, fault, or alarm codes. There are 9 possibilities....
Fanuc Servo Drives, 6050, 6057, 6058Fanuc C Series Drives, 6066, 6089, 6090Fanuc Alpha Servo Drives Alarm Codes A06B-6079-H, A06B-6096-H, etc Alarm CodeFaultRemedy – Not Ready Drive is Good 0 Control Ready Drive is Good 1 Internal Fan Stopped Replace/Repair Servo Drive 2 Low control ...
ALARM CODES FOR FANUC CNC MACHINE TOOL PARTS Critical FANUC CNC component failure such as excessive current, faulty memory, blown fuses or signal mismatch throws an error and brings your CNC machinery to a grinding halt. Tri Star CNC Services providescomprehensive alarm code listsfor servo amplifier...
Fanuc 6 Alarm Codes applies to Fanuc System 6M 6T CNC controls. For cnc machinists who work on cnc lathe with 6T or CNC mill with Fanuc 6M cnc control. Fa
如果加工模具,还需要使用SERVOGUIDE进行调整, 对于特定的机床,有些参数还需要手动修改,比如,加减速时间常数,快速,切削进给,,对于大型的机床,或者机械刚性较差的机床,必须适当加大时间常数的设定。数字伺服参数设定、主要参数调整及维修 中国机电设备与维修改造技术协会&北京蓝拓机电设备有限公司 2005年7月中国机电设备与维...
ERROR (EXT) 387 n AXIS : ABNORMAL ENCODER (EXT) Servo alarms 400 SERVO ALARM: n–TH AXIS OVERLOAD (Fanuc 16iP Model A/B – 18iP Model B) 401 SERVO ALARM: n–TH AXIS VRDY OFF 402 SERVO ALARM: SV CARD NOT EXIST 403 SERVO ALARM: CARD/SOFT MISMATCH 404 SERVO ALARM: n–TH AXIS ...
In FIG. 1, the axis control circuit 16, servo amplifier 40, and servomotor 50 are each shown as being only one in number. Actually, however, these elements are provided corresponding in number to the axes of the machine tool to be controlled. If the controlled machine tool has three axes...
In the main unit2, necessary information is stored in at least one of nonvolatile memories provided to be associated with encoders of servomotors for driving first to third axes of the robot mechanism10. In this embodiment, data of D-H parameters regarding the first to third axes are respec...