1. 解释"addrconf(netdev_up): eth0: link is not ready"错误信息含义 该错误信息表明系统试图激活网络接口eth0时,发现物理链接尚未准备好。这通常意味着网络连接没有建立,可能是因为网络电缆未连接、交换机或路由器未启动,或者网络接口本身存在问题。 2. 提供可能导致此错误的原因 物理连接问题:网线未插好或损坏...
r8169 0000:05:00.0 eth0: link down IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 二.解决办法 2.1.首先使用的是哪个型号的网卡呢? 在终端输入lspci,笔者输出的网卡相关信息如下: Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller ...
kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_...
1> 首先笔者先是克隆机网络全部是down,然后出现IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 2> 然后关掉克隆机,查看其他宿主机,发现都是同样错误 3> 各种启动网卡,nmcli connection 和netplan apply等均无作用 4> 后来发现是笔者因为前一天打PUBG把很多VM服务关掉,然后重启服务即可。 5> 此时所有...
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 二.解决办法 2.1.首先使用的是哪个型号的网卡呢? 在终端输入lspci,笔者输出的网卡相关信息如下: Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller (rev 05) ...
In my customer board, referenced from sabreauto-ai board, the eth0 link is not ready. could some one give me some advice? I really confused for some days. the log is as below: ===log below=== root@sabreauto_6q:/ # eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_add...
ADDRCONF(NETDEV_UP): eth0: link is not ready thank you in advance. system-user.dtsiUnavailable zynq-7000.dtsiUnavailable Sort by votes Sort by date vicentiu Digilent Staff 237 5 Posted October 1, 2018 2 Questions: I assume you're using the original Zybo board, based on the...
link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IP...
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready From ifconfig, both interfaces have valid MAC addresses, but no IP addresses although the interfaces are configured for DHCP: eth0 Link encap:Ethernet HWaddr 00:04:9F:04:B3:2A UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 ...
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 我发现一个原因是在配置ip时,可能配置的ip地址被占用了,换个ip地址就成功了。 ifconfig eth0 xx.xx.xx.aaa netmask 255.255.255.0;route add default gw xx.xx.xx.254 1. 即将上面aaa改成其他的一个。