解释"ipv6: addrconf(netdev_change): eth0: link becomes ready"这条日志的含义: 这条日志表示在Linux系统中,与IPv6地址配置相关的组件(addrconf,即地址配置)检测到网络接口eth0的状态发生了变化,具体是从非就绪状态变为就绪状态。这意味着eth0网络接口现在已经准备好进行网络通信,系统可以开始在其上配置IPv6地址...
1、TCP/IP无问题:ifconfig eth0 网口存在,且ping包的时候,TX packets计数在增长,ping 127.0.0.1可以ping通。 2、网口PHY工作正常:J721E EVM和PC通过1000M以太网线连接的时候,日志口有打印“eth0: link becomes ready”和“am65-cpsw-nuss 46000000.ethernet eth0: Link is Up - 1Gbps/Full - flow con...
kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_...
link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IP...
[41991.869932] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [41991.870367] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [42035.102864] Hello, world linux@ubuntu:~/linux$ 同样我们去卸载内核模块的时候,执行指令sudo rmmod hello.ko ...
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready am65-cpsw-nuss 8000000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off $ ifconfig | grep eth.: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 eth1: flags=4099<UP,BROADCAST,MULTICAST...
1> 首先笔者先是克隆机网络全部是down,然后出现IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 2> 然后关掉克隆机,查看其他宿主机,发现都是同样错误 3> 各种启动网卡,nmcli connection 和netplan apply等均无作用 4> 后来发现是笔者因为前一天打PUBG把很多VM服务关掉,然后重启服务即可。
ADDRCONF(NETDEV_UP): eth0: link is not ready acc_open acc_release init: sys_prop: permission denied uid:1003 name:service.bootanim.exit PHY: 1:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready PHY: 1:01 - Link is Down PHY: 1:01 - Link is Up - ...
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready PHY: 0:00 - Link is Up - 1000/Full PHY: 0:01 - Link is Up - 1000/Full net_ratelimit: 95755 callbacks suppressed eth0: no IPv6 routers present net_ratelimit: 233772 callbacks suppressed ...
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 我发现一个原因是在配置ip时,可能配置的ip地址被占用了,换个ip地址就成功了。 ifconfig eth0 xx.xx.xx.aaa netmask 255.255.255.0;route add default gw xx.xx.xx.254 1. 即将上面aaa改成其他的一个。