可以通过命令display eth-trunk来查看Eth-Trunk接口的协商情况。 <HUAWEI>display eth-trunk 1Eth-Trunk1's state information is:Local: LAG ID: 1 Working Mode: STATIC Preempt Delay: Disabled Hash Arithmetic: According to SA-XOR-DA System Priority: 32768 System ID: xxxx-xxxx-xxxx Least Active-linknu...
-c display the Coalesce(聚合、联合) information of the specified ethernet card.聚合网口信息,使看起来更有规律。 -C Change the Coalesce setting of the specified ethernet card.修改网卡聚合信息。 -g Display the rx/tx ring parameter information of the specified ethernet card. 显示网卡的接收/发送环形...
<HUAWEI>display eth-trunk 1Eth-Trunk1's state information is: WorkingMode: NORMAL Hash arithmetic: According to SIP-XOR-DIP Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 8Operate status:upNumber Of Up Port In Trunk: 1 --- PortName Status Weight GigabitEthernet1/0/0 Up 1 ...
Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: umbg Wake-on: d Link detected: yes （2）[root@linux /]# ethtool -i eth1 driver: e1000 version: 5.0.43-k1 firmware-version: N/A bus-info: 06:08.1 （3）[root@linux /]# ethtool -S eth1...
ethtool DEVNAME Display standard information about device 显示该设备的标准信息。 ethtool -s|–change DEVNAME Change generic options 更改基本选项 [ speed 10|100|1000 ] //端口速率选项,单位是Mbps [ duplex half|full ] //端口半双工和全双工选项 [ port tp|aui|bnc|mii|fibre ] //端口选项,默认...
0x01TLV_type1字节0x00代表Terminator字段0x01代表Actor字段0x02代表Partner字段0x03代表Collector字段Actor_Information_Length1字节actor信息字段长度,为20字节Actor_Port2字节端口号,根据算法生成,由接口所在的槽位号、子卡号和端口号决定Actor_State1字节本端状态信息:LACP_Activity:代表链路所在的聚合组参与LACP协商的...
ActorPortName SysPri SystemID PortPri PortNo PortKey PortState GigabitEthernet0/0/9 32768 d0d0-4ba6-ac20 32768 1 305 10111100 GigabitEthernet0/0/10 32768 d0d0-4ba6-ac20 32768 2 305 10111100 输出信息显示,此时链路运行模式为LACP模式,并且最大活动接口数阈值是8条链路。同时G0/0/9和G0/0...
Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: d Current message level: 0x00000033 (51) drv probe ifdown ifup Link detected:yes ethtool 运行简单,他能迅速提供配置不当的网络设备的有关信息。
Port1接口出现故障而后又恢复了正常。当接口Port1出现故障时被Port3所取代,如果在Eth-Trunk接口下未使能LACP抢占功能,则故障恢复时Port1将处于备份状态;如果使能了LACP抢占功能,当Port1故障恢复时,由于接口优先级比Port3高,将重新成为活动接口,Port3再次成为备份接口。
大中型园区网络中,也有可能存在少量汇聚/接入交换机通过手工方式添加到iMaster NCE-Campus的场景,不采用网络规划模板批量导入。此时,核心/汇聚/接入交换机间互联的Eth-Trunk链路希望通过手工创建,可按照本章节思路进行配置。 核心/汇聚/接入交换机间互联采用Eth-Trunk链路时,需注意: ...