大写的p,查看网卡的mac地址、ip ad和ifconfig等命令均可实现这种功能。 [root@localhost~]# ethtool -P eno1Permanentaddress:08:94:ef:9c:13:ea[root@localhost~]# ip ad |grep -i eno1 -A 14:eno1:<NO-CARRIER,BROADCAST,MULTICAST,UP>mtu1500qdisc mq stateDOWNgroup default qlen1000link/ether08:9...
Yes that would be helpful. Can you clarify under what conditions you are able to detect link and when you are not? My initial understanding was that the PHY could link but was not detected by the software, has that changed? Regards, ...
# for i in $( ls /sys/class/net ); do echo -n $i; ethtool $i | grep Link\ d; done eth0 Link detected: yes eth1 Link detected: no lo Link detected: yes wlan0 Link detected: no NOTE: The only problem with the aboveethtooloutput is that it will not detect connected cable i...
mii-tool -v eth0 eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:aa:00, model 56 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10b...
link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD 从以上信息中可以看出,这块网卡工作在100M全双工自适应模式下,“100BaseTx-FD”意为100M Full Duplex。 2. 更改网卡的工作模式,输入命令: #mii-tool -F media [interface] media可选的模式有100baseTx-FD、100baseTx-HD、10baseT-FD、10baseT-...
Jan 28 2016 15:19:53+08:00 FW_USG9560_01LINKDETECT/4/LINKNEIGHBORCHANGE:Slot=1,Vcpu=0; 1.3.6.1.4.1.2011.5.25.135.2.1 Link neighbor information is changed.(IfName=GigabitEthernet1/0/1) Jan 28 2016 15:19:53+08:00 FW_USG9560_01SRM_ENTITY/2/PHYSICALPORTDOWN: OID 1.3.6.1.4.1.2011.5...
ethtool-执行ethtooleth0后怎么只出现了两行currentmessagelevel0x000000007(7);linkdetectdeyes 网卡没挂载把 linux下ethtool的安装方法!! 1.下载安装包:ethtool-,将其放入自己的路径下,解压:tarzxvfethtool- 2.编译安装: cdethtool-3.15 sudo./configure...
在V200R011C10之前的版本,端口只支持将速率相同的接口加入到同一Eth-Trunk接口,如GE电接口和GE光接口可以加入同一个Eth-Trunk接口。在V200R011C10及之后的版本,配置mixed-rate link enable命令后,速率不同的接口也能加入到同一Eth-Trunk接口。 设备聚合组进行负载分担计算时不支持以端口速率作为计算权重。因此,当端口...
Want to thank TFD for its existence?Tell a friend about us, add a link to this page, or visitthe webmaster's page for free fun content. Link to this page: Facebook Twitter
/** * @brief Get Ethernet PHY link status * * @param[in] phy: Ethernet PHY instance * * @return * - ESP_OK: get Ethernet PHY link status successfully * - ESP_FAIL: get Ethernet PHY link status failed because some error occurred * */ esp_err_t (*get_link)(esp_eth_phy_t *p...