准备Micro USB线,连接PC和ESPEYE开发板 打开windows10设备管理器,找到有感叹号的CP2102N USB to UART Bridge Controller的设备,说明他还没有安装驱动 官网地址:驱动获取打开上述链接,按照自己系统下载驱动,并解压和安装。 比如:win10 64位系统的下载后打开图中的“CP210xVCPInst
ESP USB Bridge 是一个 ESP-IDF 项目,能够利用 ESP32-S2 或 ESP32-S3 在计算机 (PC) 和目标微控制器 (MCU) 之间建立桥接,从而替代 USB 转 UART /JTAG 桥接芯片(例如 CP210x)。 以下是 ESP USB Bridge 的概念框图: ESP USB Bridge 创建了一个复合 USB 设备,可以通过 USB 电缆被计算机访问。以下是其...
在USB无线网卡上使用ESP32-S3芯片/模组,ESP-IDF版本为idf5.0.3时,客户在运行esp-iot-bridge/examples/wireless_nic例程时,编译烧录完成之后,电脑无法识别USB设备,这是为什么呢?解决思路 了解客户相关情况后,工程师克隆esp-iot-bridge库运行例程测试,成功复现问题,经过相关测试及案例分析,发现此过程需要开启相应配置。...
Morecat Lab WiFi-BareBoard32 WiFi-BB32 Repository Photos: 2017 July 31: Bare board 2017 Aug 1: Assembled & comparison photo 2017 Sept 12: comparison photo Morgan Allen LoRaNeT32 A Wi-Fi/BLE-to-LoRa bridge with ESP32, RN2483, LiPo charge controller, and SiLabs CP2102N USB-to-UART. Ha...
CP2104 is a highly integrated USB to UART bridge controller, which is responsible for the communication protocol conversion from the host to the host computer, so as to facilitate the program burning and serial debugging of the host. The development board is equipped with an automatic download ci...
Infrared remote controller (TX/RX, up to 8 channels) Motor Pulse-width modulation LED Pulse-width modulation (up to 16 channels) Hall effect sensor Ultra low power analog pre-amplifier Security: IEEE 802.11 standard security features all supported, including WFA, WPA/WPA2 and WLAN Authentication...
ttyUSB0 is `CP2102N USB to UART Bridge Controller` (checked by connecting one and then the other and with linux dmesg enumeration events) the results are the following: Code: Select all | Test | `USB CDC on boot` | upload | serial timeout | output | output | | :--- | ---:...
在Windows环境下先通过uart下载hello工程进入模组,然后再调用“openocd-f board/esp32s3-builtin.cfg”,会每隔10秒打印一次信息;因为有重启原因,于是换成烧录 blink示例,随后启动openocd 后,可以直接在 blink 目录下 idf.py gdb,应该会在 app_main 停下来。
Description of Change ESP32-P4 has UART default pins only for UART0 and UART1. This PR allows the board definition from pins_arduino.h to define RX2 ... RX4 and TX2 ... TX4 if necessary. It also so...
_VIA_UART is not set CONFIG_BRIDGE_SERIAL_VIA_USB=y CONFIG_MODEM_RESET_GPIO=0 CONFIG_BRIDGE_MODEM_PPP_APN="internet" CONFIG_BRIDGE_MODEM_PPP_AUTH_USERNAME="espressif" CONFIG_BRIDGE_MODEM_PPP_AUTH_PASSWORD="esp32" # CONFIG_BRIDGE_MODEM_PPP_AUTH_NONE is not set # CONFIG_BRIDGE_NEED_SIM_...