是的,一般情况下开发板上都会有一个 USB 转串口芯片来连接 ESP32 的硬件串口,但如果引脚资源特别吃紧的话,也是可以直接用 ESP32 的 USB 外设来虚拟串口的,同样也支持程序烧录,Arduino 官方推出的开发板Arduino Nano ESP32就是这么干的。 ESP32S3 的 USB 支持两种模式,分别是USB-Serial-JTAG
环境win11 ESP IDF4.4.1 ESP32S3 测试用例代码如下: void tinyusb_cdc_rx_callback(int itf, cdcacm_event_t *event) { /* initialization */ size_t rx_size = 0; static uint32_t recv_total_len = 0; static uint32_t count = 0; /* read */ esp_err_t ret = tinyusb_cdcacm_read(...
然后,下拉并选择“USB JTAG/serial debug unit (Interface 1)”,选择新的驱动程序为“USB串行 (CDC) - 通信设备类”。点击“更新/安装驱动程序”,然后等待进程完成。 之后再选择USB JTAG/serial debug unit (Interface 2),新驱动选择为libusbK,然后点更新。 IDF工程配置 首先,先看一下USB CDC的端口号,我这里...
在带有集成 USB 串行/JTAG 控制器的芯片 ESP32-S3上,可以使用该控制器实现串行端口 (CDC) 的部分来实现串行控制台,而不是使用带有外部 USB-UART 桥接芯片的 UARTESP32-S2/S3 引导加载程序不支持 Windows 7 或 8 的 USB 串行。(请参阅https://github.com/espressif/arduino-esp32/issues/5994)请更新到 ...
除了通用的通信之外,CDC-ACM 接口还可以复位 ESP32-S3 并选择使其进入下载模式,从而烧录新的固件。这一功能可通过设置虚拟串口的 RTS 和 DTR 线来实现。 当我们的程序没有操作USB,完全按照eFuse的配置让USB工作以后,在Linux主机下看到的设备枚举信息如下: ...
ESP32-S2/S3 等芯片内置 USB-OTG 外设,它包含了 USB 控制器和 USB PHY,支持通过 USB 线连接到 PC,实现 USB Host 和 USB Device 功能。 而ESP32-S3通过USB-OTG接口就可以实现USB虚拟串口(CDC-ACM类)功能。 什么是USB虚拟串口? USB虚拟串口是一种可以让微控制器(如ESP32-S3)通过USB接口与电脑进行串口通信...
ESP32S3-CORE开发板特别注意 通过USB转串口烧录一定要安装CH343的驱动才能正常下载固件,默认的CDC驱动只能打印日志,但是速率太慢会导致下载失败。驱动传送门 通过USB下载(USB直连)可以直接烧录,Win8及以上系统无需安装驱动。可以正常使用Luatools烧录,但是无法使用LuatIDE。除烧录时需要选择带USB字样的固件,GPIO19/20会...
I have some trouble to reflash the ESP32S3 after activating the USB-CDC (tinyUSB). So basically the only option at the moment is to press the button to go into the bootloader mode at startup to reflash the device. Now assume I have the device connected to a SBC in the field and co...
1、USB CDC On Boot(USB Communications Device Class On Boot) ESP32S3芯片内置USB接口,支持USB CDC,说明可以跳过USB转串口芯片对模组进行下载。有两个选项:Enable:这种选项是要在没有串口芯片的情况下选择;Disable:有串口芯片,选择Disable。 注意:当USB CDC On Boot选择为Enable,但是板子又有串口芯片,这时候串口...
I have tried all available examples in ESP-IDF related to USB communication, including both the Host CDC and Host USB libraries, but I am unable to establish communication with my UPS device. I can successfully communicate with other devices using known drivers like CP210x, but I am strugglin...