我卸载了驱动删除了驱动程序,因为单片机支持UART和JTAG所以插入电脑后会识别为两个驱动分别对应着两个功能 UART驱动使用的是CP210x下载地址:CP210x USB to UART Bridge VCP Drivers - Silicon Labs (silabs.com) JTAG驱动使用的是乐鑫官方驱动下载地址:Configure ESP32-S3 Built-in JTAG Interface - ESP32-S3 - ...
然后,下拉并选择“USB JTAG/serial debug unit (Interface 1)”,选择新的驱动程序为“USB串行 (CDC) - 通信设备类”。点击“更新/安装驱动程序”,然后等待进程完成。 之后再选择USB JTAG/serial debug unit (Interface 2),新驱动选择为libusbK,然后点更新。 IDF工程配置 首先,先看一下USB CDC的端口号,我这里...
问题调试 在安装了USB JTAG (Interface 2)驱动的情况下,开始调试JTAG,执行“openocd-f board/esp32s3-builtin.cfg”,此命令是启动OpenOCD,但执行报错: 在JTAG指导文档中有介绍:对于带有用于 JTAG 连接的 FT2232H 或 FT232H 芯片的定制板,或带有ESP-Prog 的定制板,可执行“board/esp32s3-ftdi.cfg”,建议客...
usb1-4: New USB device found, idVendor=303a, idProduct=1001, bcdDevice=1.01usb1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3usb1-4: Product: USB JTAG/serial debug unit usb1-4: Manufacturer: Espressif usb1-4: SerialNumber:48:27:E2:E1:E5:30cdc_acm1-4:1.0: ttyAC...
我是使用的 ESP32S3,因此选择 esp32s3 选项,接着会跳出连接方式选择,我使用的是 USB-JTAG,自然也是选择 USB-JTAG 作为连接方式: 选择好芯片后还需对 SDK 和例程进行配置,如 LED 的引脚号和工作模式等,此时点击 COMMANDS 下的 SDK Configuration Editor 也就是 menuconfig: ...
把MTCK (GPIO39) ,接到外部设备之后,在代码里面初始化之后,就不能识别到USB口了( USB JTAG/serial debug unit)。只要不初始化这个引脚,就能够正常识别到USB口。 #defineVEXT_PIN (GPIO_NUM_39)#defineGPIO_OUTPUT_PIN_SEL (1ULL<<VEXT_PIN)voidtau_gpio_init(void){//zero-initialize the config structur...
在带有集成 USB 串行/JTAG 控制器的芯片 ESP32-S3上,可以使用该控制器实现串行端口 (CDC) 的部分来实现串行控制台,而不是使用带有外部 USB-UART 桥接芯片的 UARTESP32-S2/S3 引导加载程序不支持 Windows 7 或 8 的 USB 串行。(请参阅https://github.com/espressif/arduino-esp32/issues/5994)请更新到 ...
1.进入项目文件夹,执行以下指令 2.进入下载模式之后,ubantu会识别出USB JTAG/serial debug unit,使用一下命令进行下载 3.下载完成之后,重启退出下载模式。此时 ubantu 仍然会识别出USB JTAG/serial debug unit。 链接:https://www.dianjilingqu.com/614336.html...
in my custom board based on ESP32-S3 I have a USB to UART device connected to the UART0. Then I have the inner USB/JTAG connected which allows me JTAG debugging. At the moment I use the external USB to UART as shell console. I see the log on both UART (the UART0 and the por...
If anyone drops the bytes, that would be the VFS driver (in this case, usb_serial_jtag_write function). The USB Host polling rate is well below this afaik (like ~15ms), so this should only happen when USB is malfunctioning of unplugged. I think in practice the serial port driver on...