在Cisco交换机上，默认配置指的是交换机恢复出厂设置后的配置。恢复出厂设置是指将设备的配置还原为初始状态，删除任何已进行的更改和自定义设置，包括端口和 VLAN 的配置等。对于Cisco交换机，恢复出厂设置后，默认情况下，所有端口都将被禁用，除了Port0。这是因为Port0通常用于进行初始配置，可以通过Port...
默认情况下,在Cisco Catalyst交换机的每个端口分配给VLAN1。其中两项建议 翻译结果2复制译文编辑译文朗读译文返回顶部 默认情况下,在一个思科催化剂开关中的每港被分配给 VLAN1。那两建议是 翻译结果3复制译文编辑译文朗读译文返回顶部 默认情况下,思科 Catalyst 交换机中的每个端口分配给 VLAN1。其中两项建议是 翻译...
Petes-Switch(config)#default interface range GigabitEthernet 0/3 - 6 How to Remove the Configuration for a Cisco ASA 5500 Port To do the same on a CiscoASAyou need a different command, you use the ‘clear configure‘ command. Note: The interface naming used here is for an ASA8885-X th...
and setting up full ip routing which according to me you must try to accomplish. then usually a subnet is created between a local routed port on the switch and the isp. you then route local traffic to the local routed port : https://www.cisco.com/c/en/us/support/docs/sw...
interface is set to trunk, desirable, or auto mode. I used to see this mode as the default on some switches, but not any longer. This is now the default switch port mode for all Ethernet interfaces on all new Cisco switches. switchport mode trunk Puts the interface into permanent trunking...
interface is set to trunk, desirable, or auto mode. I used to see this mode as the default on some switches, but not any longer. This is now the default switch port mode for all Ethernet interfaces on all new Cisco switches. switchport mode trunk Puts the interface into permanent trunking...
MHM Cisco World VIP 02-16-2024 09:04 AM 1- switchport access vlan cannot use with trunk mode interface 2- switchport trunk encap 802.1q This command not need any more in new SW' only old SW support 802.1q and ISL need this command new SW not need it MHM 1 Help...
VTP向所有活动的trunk接口(ISL或802.1Q)发送更新(注意这个前提条件),一般情况下,Cisco交换机的默认配置是无VTP域名的服务端模式,所以它不会发送任何VTP更新。 配置示例: Switch1#conf t Switch1(config)#vtp domain work --配置VTP域名,Switch1可以发送更新了 ...
在一台Cisco Catalyst 2950交换机上作如下配置: Switch # config terminal Switch (config) # interface fastethernet 0/1 Switch (config-if) # switchport mode access Switch (config-if) # switchport access vlan2 若要将fastethernet 0/1端口还原到默认配置状态,可以使用()命令。 A、Switch (config) # ...
12.0(5)XE This command in DSP farm interface configuration mode was modified. 12.1(1)T The DSP farm interface configuration mode modification was integrated into Cisco IOS Release 12.1(1)T. 12.2(2)XA This command was implemented on the Cisco AS5300. 12.2(11)T This command was implimented ...