Interface line width(顶层线宽):底座的线宽。一般设0.4即可。Airgap(空隙):底座与图形表面的距离,一般设0.22,利于拆卸。Suface layers(表层):底座的表层打印数量,这些层是完全填充的层。Fix horrible(修补缺陷):Combine everything(Type-A):尽量保持内孔不变Combine everything(Type-B):忽略所有内孔,只保持外部...
With some support structure types, the supports can be quite unstable if thin strips are generated. With this setting enabled, the endpoints of the support structures will be connected. This can add more material but increases the reliability of the structures and prints with a more even flow r...
Interface line width(顶层线宽):底座的线宽。一般设 0.4 即可。 Airgap(空隙):底座与图形表面的距离,一般设 0.22,利于拆卸。 Suface layers(表层):底座的表层打印数量,这些层是完全填充的层。 Fix horrible(修补缺陷): Combine everything(Type-A):尽量保持内孔不变 Combine everything(Type-B):忽略所有内孔,...
Support Line Width:The line width of support structures. Support Interface Line Width:The width of a single support interface line. The line widths for the support interface roof and floor can be adjusted separately. Prime Tower Line Width:The width of a single prime tower line. Initial Layer ...
Interface line width(顶层线宽):底座的线宽。一般设 0.4 即可。 Airgap(空隙):底座与图形表面的距离,一般设 0.22,利于拆卸。 Suface layers(表层):底座的表层打印数量,这些层是完全填充的层。 Fix horrible(修补缺陷): Combine everything(Type-A):尽量保持内孔不变 Combine everything(Type-B):忽略所有内孔,...
接口层线宽(Interface ling width)一般细一些,接口层厚(Interface thickness)和层厚相同即可。新版本的Cura 添加了空气沟(Airgap)和表面层(Surface layers)两个参数,第一个参数是控制底垫上面和模型底面的间隙,在这个间隙中不打印任何填充物,因此叫“空气沟 48、”,这个空气沟的存在有利于模型和底垫的分离。表面...
;jerk_support_interface:{jerk_support_interface} ;jerk_support_roof:{jerk_support_roof} ;jerk_topbottom:{jerk_topbottom} ;jerk_travel:{jerk_travel} ;jerk_travel_layer_0:{jerk_travel_layer_0} ;jerk_wall:{jerk_wall} ;jerk_wall_0:{jerk_wall_0} ...
- Support Interface Priority - Tree Support Limit Branch Reach - Tree Support Optimal Branch Range - Tree Support Rest Preference Please note Due to the holiday season, responses from UltiMaker might be slower than usual. Please remember that this UltiMaker Cura alpha is not suitable for ‘normal...
"support_interface_material_flow": { "value": "material_flow" }, "support_interface_offset": { "value": "1 if extruder_nr == support_extruder_nr else 0" }, "support_interface_pattern": { "value": "'lines'" }, "support_interface_wall_count": { "value": "1 if extruder_nr ==...
For the UltiMaker Method series machines Support Interface, Tower, and Horizontal Expansion settings have been updated. For all UltiMaker Machines the Zseam settings have been updated so they are smartly hidden, except for the visual intents. ...