Phase Diagrams and Physical Properties of Nonequilibrium AlloysNonequilibrium Phase Diagrams of Ternary Amorphous AlloysSummary This document is part of Subvolume A 'Nonequilibrium Phase Diagrams of Ternary Amorphous Alloys' of Volume 37 'Phase Diagrams and Physical Properties of Nonequilibrium Alloys' ...
Experimental investigation and thermodynamic calculation of the phase equilibria in the Cu–Sn and Cu–Sn–Mn systems Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science, 35A (2004), pp. 1641-1654 CrossrefView in ScopusGoogle Scholar [23] M. Kantola, E. Tokola ...
Cu2(1z)MnzGa2Se4 alloys: Phase diagram and effects of Mn ordering on magnetic behaviour Cu_2(1-z)Mn_zLn_2Se_4 alloys; phase diagram and effects of Mn ordering on magnetic behaviourA.alloysA.semiconductorsD.magnetic properties... Quintero, M.,Lopez, M.,Morocoima, M.,... - Physica...
Phase Diagram of a Binary Alloy in the Static Concentration Wave Approximation Article 01 May 2018 Computational study of the \({\text{DO}}_3+{\text{L}}2_1\) two-phase field in \(\beta\) Cu–Al–Mn Article 26 October 2023 References I. M. Lifshitz,Zh. Eksp. Teor. Fiz. 11...
基于Ginzburg-Landau理论采用连续相场法模拟了Fe-15%Cu-3%Mn-x Al(质量分数x = 1%, 3%, 5%)合金在873 K等温时效时纳米富Cu析出相沉淀机制及Al含量对富Cu相析出的阻碍效应. 通过计算成分场变量和结构序参数, 研究了富Cu析出相的形貌、颗粒密度、平均颗粒半径、生长和粗化动力学. 研究结果表明:在时效早期阶段,...
The following are two examples of recommended layouts: ‣ Packed Row-major: dim [B,M,N] with stride [MN, N, 1], or ‣ Packed Column-major: dim [B,M,N] with stride [MN, 1, M] Unpacked layouts for 3-D tensors are supported as well, but their support surface is more ragged...
The terminal solid solution in Cu-rich end of the phase diagram has maximum solubility of 6.93 at% Mg. MgCu2 has fcc C15-type structure and this has a composition range of 64.7 to 69 at%Cu. Stoichiometric MgCu2 has a melting point of 797°C [253]. Similar to dilute Cu-Mn alloys,...
结果表明:FeCrNiCoCu 及 FeCrNiCoMn 高熵合金均为单一的 FCC 结构,其中 FeCrNiCoMn 态密度达到最大值时对应的能量较低,结构更趋于稳定,耐蚀倾向性好.FeCrNiCoMn 高熵合金在三种溶液中的 耐蚀性均高于 FeCrNiCoCu 的,这是由于 Cu 元素的存在会引起元素偏聚,降低了合金的耐蚀性.而 Mn 元素以 金属间化合物...
Under a controlled load of 30 mN, the hardness of the MMLs in the NC W–Cu and HN W–Cu composites is 5.6 and 9.7 GPa, respectively. Therefore, the excellent wear resistance of the HN W–Cu composite can be attributed to the formation of a protective film with excellent combined ...
found that the inner cracking of nanoporous Cu (np-Cu) can be reduced by microalloying of the Cu–Mn precursor alloy with Si [20]. As indicated above, recent endeavors to improve the mechanical properties of dealloyed nanoporous metals have been mainly focused on suppressing crack formation ...