To configure R1 as a DHCP server in Cisco Packet TracerConfigure R1 as the DHCP server R1> enable R1# configure terminal R1(config)# ip dhcp pool LAN_POOL R1(dhcp-config)# network 192.168.1.0 255.255.255.0 R1(dhcp-config)# default-router 192.168.1.1 ...
In such a situation, you need to configure the router's interface connected to the DHCP server as a DHCP relay agent. To configure a router's interface as a DHCP relay agent, use the following command in interface configuration mode. Router(config-if)#ip helper-address [ip-address-of-the...
Just change the managment vlan ip address ;which is vlan1 to same as your dhcp pool in each switch .You have dhcp pool of network 10.10.10.0 on corp switch but you have ip address of 172.31.1.1 on vlan1 .Its two different network and switch will not do router's work unless you make...
We have already discussed the first option in the previous part of this tutorial. In this part, we will learn how to create and configure multiple DHCP pools on the DHCP server and assign a DHCP pool to each VLAN through a packet tracer example. This tutorial is the fifth part of t...
default-router 192.168.20.1dns-server 8.8.8.8 9.9.9.9!ip dhcp pool Nativenetwork 192.168.80.0 255.255.255.0default-router 192.168.80.1dns-server 8.8.8.8 9.9.9.9!ip dhcp pool Mgtnetwork 192.168.99.0 255.255.255.0default-router 192.168.99.1dns-server 8.8.8.8 9.9.9.9!!!ip cefno ipv6 cef!multi...
AAA Only—If you select the Authentication Server as RADIUS, by default, the Authorization Server has the same value. Select the Accounting Server from the drop-down list. Whenever you select AD and LDAP from the Authentication Server drop-down list, you must select the Authorization Server and...
ASAv(config-if)#security-level 100 ASAv(config)#interface GigabitEthernet0/1 ASAv(config-if)#ipv6 address fd02::2/64 ASAv(config-if)#nameif outside ASAv(config-if)#security-level 0 U zou nu de basisverbinding van Layer 2 (L2)/Layer 3 (L3) aan een upstream rout...
ASAv(config)#interface GigabitEthernet0/1 ASAv(config-if)#ipv6 address fd02::2/64 ASAv(config-if)#nameif outside ASAv(config-if)#security-level 0 You should now have the basic Layer 2 (L2)/Layer 3 (L3) connectivity to an upstream router on the outside VLAN at addressfd02::1...
ip dhcp pool Officenetwork 192.168.10.0 255.255.255.0default-router 192.168.10.1dns-server 8.8.8.8 9.9.9.9!ip dhcp pool Customersnetwork 192.168.20.0 255.255.255.0default-router 192.168.20.1dns-server 8.8.8.8 9.9.9.9!ip dhcp pool Nativenetwork 192.168.80.0 255.255.255.0default-router 192.168.80.1dns...
ip dhcp excluded-address 10.10.10.1 ! ip dhcp pool Corp_LAN network 10.10.10.0 255.255.255.0 default-router 10.10.10.1 dns-server 4.4.4.4 ! Note: Configuration is correct in all the switches. DHCP is configured in every Switch like above. Only IP Addresses are differ according to requirement...