This would streamline your process by grouping VLANs, by using a single task to create the trunk configuration. Might look like (please double check this!) - name: Define VLANs and EPGs set_fact: vlan_epg_map: - vlan: 10 epg: "VLAN_10" - vlan: 20 epg: "VLAN_20" - vlan:...
-- Select GigabitEthernet 1 for the trunk configuration. !-- No Layer 3 (L3) configuration is done here. Router(config)#interfaceGigabitEthernet1 Router(config-if)#no shut Router(config-if)#exit !-- Enable dot1q on the sub-interface one for each VLAN. !-- Configure L3 information on ...
transitions to forwarding state: 1 The port is in the portfast mode by portfast trunk configuration Link type is point-to-point by default BPDU: sent 6063, received 0 Port 11 (GigabitEthernet1/0/11) of VLAN0010 is designated forwarding Port path cost 4, Port priority 128, Port Identifier ...
I've already configured each port separately - the configuration is exactly the same (1:1). Trunk allows particular VLANs only. Now, let's go to the port-channel configuration. 1. Do I have to configure trunk mode on port-channel even if it's been already been done for each port? I...
switch(config-if)#switchport trunk allowed vlan 1。2 ---设置同意的vlan。默认不用配置。为全部vlan switch(config-if)#switchport trun native vlan 999 ---设置trunk口的native vlan 5、port状态 switch(config)# switch(config)#int fa0/3 switch(config-if)# switch(...
swilchport trunk encapsulation (isl I dot1q I negotiate)配置trunk 封装ISL或 802.1Q 或 自动协商 switchport mode (dynamic (auto I desirable) trunk) 配置二层 trunk 模式。 dymamic auto—自动协商是否成为trunk dynamic desirable-把端口设置为trunk如果对方端口是trunk, desirable,配置Native VLAN ...
我们假设核心交换机名称为:com;分支交换机分别为:par1、par2、par3,分别通过port 1的光线模块与核心交换机相连;并且假设vlan名称分别为counter、market、managing……需要做的工作:A、设置vtp domain(核心、分支交换机上都设置)B、配 Cisco 三层交换机 原创 gywxdn 2013-06-27 09:56:13 3288阅读 ...
Configuration Example and Explanation 2. Port 以太网端口有三种链路类型:access、trunk、hybird Access类型端口:只能属于1个VLAN,一般用于连接计算机端口; Trunk类型端口:可以允许多个VLAN通过,可以接收和发送多个VLAN 报文,一般用于交换机与交换机的连接。 Hybrid类型端口:可以允许多个VLAN通过,可以接收和发送多个VLAN 报...
2 新建 NEW VSAN2 将port转移VSAN2里面,建议创建VSAN2 把端口放置在VSAN2中 2. 交换机配置 2.1. 配置交换机管理地址 switch# config t(按tab命令可以补全的或者 输入命令后空格加? 可以出来命令的使用方法) switch (config)# switchname switch switch(config)# interface mgmt 0 ...
这个是端口安全违规的默认动作。默认的端口安全配置：以下是端口安全在接口下的配置- 特性：port-sercurity 默认设置：关闭的。特性：最大安全mac 地址数目默认设置：1 特性：违规模式默认配置：shutdown，这端口在最大安全mac 地址数量达到的时候会shutdown，并发snmp 陷阱。配置向导：下面是配置端口安全的向导- ...