switchxxxxxx(config)#spanning-tree mode mst spanning-tree forward-time Use thespanning-tree forward-timeGlobal Configuration mode command to configure the spanning-tree bridge forward time, which is the amount of time a port remains in the listening and learning states before entering the...
Switch(config)#spanning-tree mode rapid-pvst 指定root/secondary root Switch(config)#spanning-tree vlan 1 root primary Switch(config)#spanning-tree vlan 1 root secondary 指定交换机的优先级 Switch(config)#spanning-tree vlan 1 priority priority 查看 Switch#show spanning-tree vlan vlan-id...
Il comandospanning-tree pseudo-informationè stato originariamente sviluppato per le progettazioni di PC virtuale (vPC) e vPC+ per consentire agli utenti di creare una topologia di switch peer vPC e non vPC ibridi. A tal fine, lo switch invia due diverse priorità BPDU. Sebbene questo coman...
Switch1的STP情况: Switch0的f0/2接口阻塞,Switch0不是作为根桥。未进行配置默认情况下,结果如图所示。 那么,现在要将S0设置为根桥了,手动进行配置。操作就是将Priority设置为4096,前面提到BPDU决定根桥的因素之一。 命令: spanning-tree vlan1priority4096 将S0优先级设置之后,根桥变为S0,这时以S0向网络发送数据...
On all other uplink ports I have the cisco switch macro applied except this port Thanks tony Hello, There's a problem in a spanning-tree between your fw and Cat4k. I don't know if NetScreen firewallsupports VLANs on its ports, and if yes - ...
当然Switch2也可以是根交换机。但记住,在这个网络拓扑中,只有一个根交换机。 这里我们要尝试一下改变交换机的优先级,就是换个根交换机看看。在这里我们挑选Switch0来进行试验,在进行show spanning-tree发现32769,然后使用spanning-tree vlan 1 priority +优先级的值 来设置优先级 当设置完成后,Switch0就成为了根...
1.switch(config)#hostnamehostname switch(enable)setsystemnamename-string 2.在基于IOS的交换机上设置登录口令: switch(config)#enablepasswordlevel1password 在基于CLI的交换机上设置登录口令: switch(enable)setpassword switch(enable)setenalbepass 3.在基于IOS的交换机上设置管理IP: ...
或SA(config)#spanning-tree root primary //也把交换机A设置根交换机。 SWITCH B: SB(config)#spanning-tree priority 5000 //配置优先级值比A交换机大一点,比默认值小,配置成备用根交换机。 或SB(config)#spanning-tree root secondary //也可以配为备用根交换机。
Switch(config-if)#exit # MSTP配置 vlan10,20为主根,vlan30,40 为次根 switch(config)#spanning-tree mode mstp switch(config)#spanning-tree mst configuration switch(config-mst)# name Cisco switch(config-mst)#revision 1 switch(config-mst)#interface 1 vlan 10,20 ...
一、何謂Spanning-Tree 二、建置SpanningTree迴圈保護機制 三、設定SpanningTree教學 -3 一、何謂Spanning-Tree 若是沒有SpanningTree迴圈保護機制 當Host送出一個BroadcastFrame(例如ARPRequest)至Router時, Frame將會被SwitchA收到。SwitchA辨認Frame中的Destination ...