Use thespanning-treeGlobal Configuration mode command to enable spanning-tree functionality. Use thenoform of this command to disable the spanning-tree functionality. Syntax spanning-tree no spanning-tree Default Configuration Spanning-tree is enabled. Command Mode Global Configuration mode Exampl...
H3C的交换机与Cisco的交换机之间进行互联的时候不但必须要用802.1q(没办法,这是标准),而且在spanning-tree上H3C交换机也有些特殊的地方需要注意。 不知道基于什么考虑H3C的E328交换机默认没有启用spanning-tree协议,因此当出现环路的时候会产生严重的广播风暴,需要在system-view上执行stp enable命令启用spanning-tree H3C...
nfvis(config-switch)#spanning-tree mode mstnfvis(config-switch)#commitnfvis(config-switch)#end spanning-tree mst configuration Use thespanning-tree mst configurationcommand to enable configuring an MST region by entering the MST mode. spanning-treemstconfiguration ...
级一样根据端口优先级决定拓扑结端口优先级配置步骤步骤1configspanningtree进入spanningtree配置模式并配置生成树模式步骤2spanningtreemodemst配置mst工作模式步骤3spanningtreeportprioritymst配置端口的优先级步骤4exit退出spanningtree配置模式步骤5showspanningtreemst显示mstp配置mstinstance时候显示的是ist的信息其他的为msti...
在 SPAN 会话被激活的状态下,目的端口其实不参加 spanning tree 。注意在缺省状态下,目的端口封闭从网络流入互换机的数据。假如作测试,要将端口的该选项翻开。 3.源端口( Source Port )源端口是一个被监听用以进行网络流量剖析的互换机端口。 经过源端口的数据流量能够被分为流入,流出,或许流入和流出三种种类。在...
S(config)# enable password|secret privilege_password 配置特权口令(加密或不加密) S(config)# interface ethernet|fastethernet|gigabitethernet slot_#/port_# 进入接口子配置模式 S(config-if)# [no] shutdown 关闭或启用该接口(默认启用) S(config)# ip address IP_address sunbet_mask 指定IP地址 ...
1.在VLAN上启用生成树:spanning-treevlan22.建立根网桥:(1)直接建立:spanning-treevlan2rootprimary(2)通过修改优先级建立:spanning-treevlan2priority24768(4096的倍数,值越小,优先级越高.默认为32768)3.确定路径.选定根端口:(1)可通过修改端口成本:(在配置模式下)spanningtreevlan2cost***(100m为19,10m为100...
no service password-encryption!hostname Switch!!!spanning-tree mode pvst!interfaceFastEthernet0/1!// 此处省略部分配置信息interfaceFastEthernet0/22!interfaceFastEthernet0/23!interfaceFastEthernet0/24!interfaceGigabitEthernet1/1!interfaceGigabitEthernet1/2!interfaceVlan1no ip address shut...
或SA(config)#spanning-tree root primary //也把交换机A设置根交换机。 SWITCH B: SB(config)#spanning-tree priority 5000 //配置优先级值比A交换机大一点,比默认值小,配置成备用根交换机。 或SB(config)#spanning-tree root secondary //也可以配为备用根交换机。
第一条命令在特权模式(enable)下执行,其他都是在配置模式(configure terminal)下。 这次实验只涉及到第1、2条命令,为基础运用。 show spanning-tree 如下,可以看到交换机生成树具体信息,分为两部分:根ID 和桥ID. Priority:优先级(参数范围:<0-61440>) ...