Switch#show version | be Mode Switch Ports Model SW Version SW Image Mode --- --- --- --- --- --- * 2 60 C9500-12Q 16.12.4 CAT9K_IOSXEBUNDLE<--- Switch#show run | inc boot system boot system bootflash:cat9k_iosxe.16.12.04.SPA.bin<---BUNDLE mode .bin image S...
> show version ---[ FPR2130-2 ]--- Model : Cisco Firepower 2130 Threat Defense (77) Version 7.0.5 (Build 72) UUID : 6ba86648-2749-11ee-b7c9-c9e434a6c9ab VDB version : 338 --- 任务2.在高可用性下配置Secure Firewall设备管理器 网络图 根据下图配置主用/备用高可用性(HA...
Switch#deletevlan.dat Delete filename[vlan.dat]?vlan.dat Delete flash:/vlan.dat?[confirm]Switch# 第十六步: show flash 命令 代码语言:javascript 复制 switch#show flash file name filelength nos.img1720035betys//交换机软件系统startup-config 0betys//启动配置文件当前内容已配置running-config 783bety...
show interface eth1/43 transceiver detials | include dBm 注释:查看思科设备1/43端口光衰值,主要查看Rx Power行的Current Measurement值为:-2.51dBM 4.juniper 设备查看光衰的命令 show interfaces diagnostics optics ge-0/1/1 5、中信设备查看光衰值命令等等 show optical-inform brief interface xgei-0/1/0/2...
Step 1. Open a SSH connection to the Catalyst 9300 switch Step 2. Check the subscription configured on the device using the following IOS XE CLI C9300# show run | sec telemetry Lets analyze the main parts of the subscription configuration: telemetry ietf subscription 101 (subscription ID) enco...
switch #configure terminal switch(conf)#hostname aptch2950 aptech2950(conf)# interface fastehernet 0/17 aptech2950(conf-if)# 09查看命令show switch>enable switch#show version 查看系统中的所有版本信息 show interface vlan 1 查看交换机有关IP协议的配置信息 ...
1 switch#show version 查看系统中的所有版本信息 2 switch#show ip int b 查看各接口状态 3 switch#show vlan int b 查看交换机所有vlan信息 4 switch#show running-configure 查看交换机当前起作用的配置信息 5 switch#show int f0/0 查看指定端口信息 ...
5)通过show run命令查看路由器配置的密码,更改密码 6)修改配置寄存器的值,并保持配置 Router(config)#config-register 0x2102 Router(config)#exit Router#copy running-config startup-config #交换机的密码恢复: 1)拔掉交换机的电源插头 2)重新插好电源后,立即按住交换机上的mode键,当看到配置界面显示“switch”...
Switch#show vlan brief 查看vlan信息 删除vlan Switch (config)# no vlan vlan-id 删除Vlan 将接口g0/1加入vlan2 如果是Trunk口设置允许访问的vlan,下面trunk篇有详细介绍 设置接口状态 多数Cisco 交换机默认具有处于非连接状态的端口。 这表示端口当前没有连接到任何设备,但如果将其连接到其他正常运行的设备,它将...
对于Cisco光纤交换机,可以通过命令:show version 获取到交换机的版本信息,如下所示: switch(config)# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html Copyrig...