不使用SMI功能並在有該命令的情況下運行Cisco IOS和Cisco IOS XE軟體版本的使用者可以使用no vstack命令停用SMI功能。 注意:Cisco IOS版本12.2(55)SE03中引入了vstack命令。 以下是在停用SMI客戶端功能的Cisco Catalyst交換機上show vstack命令的輸出示例: switch#show vstack config Role: Client (SmartInstall disabl...
启动新映像时,请使用show version命令验证新映像的版本: 注意:当您启动新映像时,引导加载程序会自动升级。 Switch#show version Cisco IOS® XE Software, Version16.06.02Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE),Version 16.6.2, RELEASE SOFTWARE (f...
switch 1-2 你试... 好的,多谢 Walter.wu Spotlight 选项 发布时间09-04-201906:26 PM 1.Converting from Install Mode to Bundle Mode https://content.cisco.com/chapter.sjs?uri=/searchable/chapter/c/en/us/td/docs/switches/lan/Denali_16-1/ConfigExamples_Technotes/Conf...
Cisco Community 思科社区 网络 交换讨论区 开机switch:模式 刷进去ios后bundle模式改成install不成功 选项 5355 10 4 开机switch:模式 刷进去ios后bundle模式改成install不成功 terrellguo Beginner 发布时间 09-02-2019 10:41 PM 哪位帮看下什么问题,怎样解决:开机switch:模式 刷进去i...
Step 1. Open a SSH connection to the Catalyst 9300 switch Step 2. Check the subscription configured on the device using the following IOS XE CLI C9300# show run | sec telemetry Lets analyze the main parts of the subscription configuration: telemetry ietf subscription 101 (subscription ID) enco...
SNMP v2还定义了两个新的协议操作:GetBulk和Inform。GetBulk操作被用于NMS高效的获取大量的块数据,如表中一行中的多行。GetBulk将请求返回的响应消息尽量多的返回。Inform操作允许一个NMS来发送trap消息给其他的NMS,再接收响应。在SNMP v2,如果agent响应GetBulk操作不能提供list中的全部变量的值,则提供部分的结果。
ssh version 2 配置ASDM(自适应安全设备管理器)接入 http server enbaleport启用功能 http{networdk | ip_address } mask interface_name asdm image disk0:/asdm_file_name指定文件位置 usernameuserpasswordpasswordprivilege15 NAT nat-control natinterface_name nat_id local_ip mask ...
switch>enable switch #configure terminal switch(conf)#hostname aptch2950 aptech2950(conf)# interface fastehernet 0/17 aptech2950(conf-if)# 09查看命令show switch>enable switch#show version 查看系统中的所有版本信息 show interface vlan 1
2.Cisco IOS设备版本信息判断 管理员用户可以登录到设备后再CLI中输入show version来查询设备版本,通过影响版本判断设备是否在影响范围内。 ios-xe-device# show version Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version Denali 16.2.1, RELEASE SOFTWARE (fc1) ...
show sessions 显示通过Telent到远程设备的连接 show start 命令show startup-config的快捷方式。显示保存在NVRAM中的备份配置 show terminal 显示配置的历史记录大、 show trunk A 显示端口26的中继状态 show trunk B 显示端口27的中继状态 show version 给出该交换机的IOS信息以及正常运行时间和基本Ethernet地址 ...