從ROMMON,您可以隨時使用set命令驗證變數。 rommon 1 >setPS1=rommon ! > ?=0 DEFAULT_GATEWAY=10.1.1.1 ETHER_SPEED_MODE=4 TFTP_RETRY_COUNT=36 SWITCH_NUMBER=1 DLC_DONE=TRUE RET_2_RTS= RET_2_RCALTS= MCP_STARTUP_TRACEFLAGS=00000000:00000000 TFTP_MACADDR=00:db:ad:ba:d0:52...
当发出中断时,配置寄存器0x2102将阻止返回到ROMMON。 默认情况下,所有9800设备(9800-40、9800-80、9800-L)都设置了配置寄存器0x2102。但是,由于它们运行基于Linux的Cisco IOSXE®,因此会忽略这一点,而防止返回ROMMON的唯一方法是配置命令no service password-recovery。
通过按住设备mode键重启,进入rommon模式 switch: 提示符表明设备处于rommon / bootloader模式。引导加载程序提供一组有限的操作来管理设备。要查看可用操作的列表,请发出 ? 命令 switch: 提示。 注意:在具有高可用性的Catalyst 9400交换机(两个管理引擎)上,执行密码恢复时,必须在通电之前删除辅助管理引擎。否则,主可以从...
ROMMON 1 >IP_ADDRESS= ROUTER的IP地址(要和TFTP服务器在同一网段内) ROMMON 2 >IP_SUBNET_MASK= ROUTER的子网掩码 ROMMON 3 >DEFAUT_GATEWAY= 默认网关地址(可以没有,也可以是TFTP服务器) ROMMON 4 >TFTP_SERVER= TFTP 服务器IP地址 ROMMON 5 >TFTP_FILE= IOS文件名(只给出文件名,不需要路径) ROMMON 6...
1.拔下交换机电源,用手按住交换机“Mode” 按钮,插上电源,等待交换机进入控制台模式。其提示符为“switch: ” 2.执行命令flash_init和load_helper switch: flash_init 初始化flash文件系统 switch: load_helper 加载load_helper命令 3.执行命令dir flash,以查看闪存的内容: ...
1- Connect the power cord to your switch (don't press anything yet). 2- As soon as the "System LED blinks rapidly" press and release the Mode button 2-3 times. The switch enters the ROMMON mode. Voila - Simple! 5 Helpful Reply 1 2 ...
Access Point ROMMON Recovery AP: prompt Recovery Here is the step by step procedure for 1140 series AP.. Its the same for almost 90% or all the Aironet product series Image used c1140-k9w7-tar.124-21a.JY.tar Assuming We have the IP 192.168.100.101
What us traditional Cisco route/switch guys would consider “ROMMON” as a loose equivalent. In this case it is important to note, since the device wasn’t function on proper firmware and was in recovery mode, the IP address of the ATA is actually in the Data VLAN at this point, NOT ...
Nuking (ROMMON, Password Recovery, etc) Interfaces Interface Selection Assign Static IP to Interface Interface Ranges Interface Verification Remove IP Addresses Console Port Change Console Baudrate DHCP Snippet: Enable Router DHCP Server Snippet: Enable Switch DHCP Server Create DHCP Pool DHCP Verif...
Recovery Procedure Cisco ROMmon Mode Recovery Procedure Cisco ROMmon Recovery Procedure CISCO Router Cisco Router factory-default Cisco Router reset password Cisco Switch AAA Security cisco switch factory default command CISCO Switch LACP Cisco Switch Port Security Cisco Switch Security Cisco Switch Security...