After the router reboots, it is in ROM monitor mode. The number in the prompt increments with each new line. ROM Monitor Commands Enter ? or help at the ROM monitor prompt to display a list of available commands and options, as follows: rommon 1 > ? alias set and ...
Use ROMMON commands: confreg 0x2142reset The switch will (re-)start but it will not load configuration saved. Use either standard config mode command "config-register 0x2102" or ROMMON command "confreg 0x2102" to revert back to standard boot mode (e.g. saved configuration is loaded during ...
In the case of the Catalyst 4500/4000, if you reload the switch after deletion of the image, you can still recover the deleted image in ROMmon mode. Issue theundelete ROM monitorcommand. The commands in this list are supported in ROMmon mode for only Catalyst 4500/4000 series switches that...
3、 修改寄存器值以后使用命令“reset”从新启动引擎。 rommon 2 > reset Resetting ... rommon 3 > 当系统从新启动以后,你进入交换机后模式的提示符就成为了“Switch> ” 通过使用命令“Switch#show version”来查看现在的寄存器值是否修改成功。 Switch#show version ---看看是不是有下面这一行 Configuration re...
type 'confreg' command.rommon 1 >rommon 1 > rommon 1 >confreg (此处修改寄存器值) Configuration Summary : => diagnostic mode => use net in IP bcast address => use all zero broadcast => break/abort has effect => ignore system config info => console baud: 9600 => autoboot from: autoboo...
rsvp RSVP Interface Commandsrtp RTP parametersverify verify dg_core(config-if)#ip 0 有帮助 回复 Rps-Cheers VIP 回复D_W 发布时间 03-18-2024 09:14 PM 可以看看3850的版本和feature。如下说明所示,PBR需要IP Service feature支持。 Policy-based routing (PBR) allows superior control...
rommon> ]] > (boot)> switch: # IOS升级备份-TFTP的方式: 把IOS 备份到TFTP服务器前的准备工作: 1. 确认可以访问TFTP服务器。 2. 确认TFTP服务器是否有足够空间来保存IOS 文件。 3. 确定文件的名称和路径。 验证闪存信息,使用show flash 命令,如下: ...
These commands wipe all config and reboot the device Note:Remeber to say "no" to saving running config on reload. If you say yes, running config will be saved and you wont be working with fresh config on reload. Basic Switch Config ...
Cisco-1(config-if) #channel-group 10 mode on //将这些接口加入到channel group 10 Cisco-1(config-if)#no shutdown 1. 2. 3. 4. 5. 6. Cisco-2(config)#interface port-channel 20 //配置Cisco2上的Port Channel 为10 Cisco-2(config-if)# switch virtual link 2 //将Cisco 2 port Channnel...
但实事上Swtich B并没有配置FEC,当Switch B的这个状态超过1分钟后,Switch A的STP就认为有环路出现,因此也就出现了err-disable。解决办法就是把FEC的模式配置为channel-group 1 mode desirable non-silent这个意思是只有当双方的FEC协商成功后才建立channel,否则接口还处于正常状态。 第二个原因就是双工不匹配。一端...