进入rommon模式解决办法 发现CiscoCatalyst交换机重启一直处于Rommom模式下，执行Confreg命令选择启动模式为1（从第一个文件启动）时，系统一直重启，无法进入正常界面。 entertoboot: 0=disableautoboot 1=thefirstfilefrominternalflashdevice 2=commandsspecifiedin'BOOT'environmentvariable [2]:1 分析认为可能IOS...
只能通过以下步骤完成 rommon 1 >confreg Configuration Summary : => load rom after netboot fails => console baud: 9600 => autoboot from: commands specified in 'BOOT' environment variable do you wish to change the configuration? y/n [n]: y enable "diagnostic mode"? y/n [n]: y enable "...
1、我把Flash卡拔掉,让系统加载rommon模式: 此时加电: Total memory size = 1024 MB - DIMM0 = 512 MB, DIMM1 = 512 MB CISCO3945-CHASSIS with C3900-SPE150/K9 with 1048576 Kbytes of main memory Main memory is configured to 72/72(dimm 0/1) bit mode with ECC enabled Readonly ROMMON initia...
Cisco IOS XE軟體提供密碼復原程式,該程式依賴於對ROM Monitor Mode (ROMMON)的存取,並在系統啟動期間使用Break鍵。在ROMMON中,可以重新載入裝置軟體,以提示包含新口令的新系統配置。 目前的密碼復原程式可讓任何具有主控台存取許可權的使用者存取裝置及其網路。無服務口令恢復功能可阻止完成Break鍵序列並在系統啟動期間輸...
Boot the WLC from ROMMON Load Image through USB Load an Image from TFTP Troubleshoot Other Useful ROMMON Commands Related Information Introduction This document describes how to recover a Catalyst 9800 controller based on ROMMON mode and no image in the flash. ...
rommon1>confreg ConfigurationSummary: =>loadromafternetbootfails =>consolebaud:9600 =>autobootfrom:commandsspecifiedin'BOOT'environmentvariable doyouwishtochangetheconfiguration?y/n[n]:y enable"diagnosticmode"?y/n[n]:y enable"usenetinIPbcastaddress"?y/n[n]:n ...
boot: image specified by the boot system commands or default to: cisco2-C2600 do you wish to change the configuration? y/n [n]: n (选择 no) You must reset or power cycle for new config to take effect rommon 2 > reset === 注意:在此时键入reset之前,开始定义串口速度(设备管理器->端口...
Use ROMMON commands: confreg 0x2142reset The switch will (re-)start but it will not load configuration saved. Use either standard config mode command "config-register 0x2102" or ROMMON command "confreg 0x2102" to revert back to standard boot mode (e.g. saved configuration is loaded during ...
ROMMON>reset 6、当提示是否进入配置对话框时（Would you like to enter the initial confinguration dialong?[yes]:),回答"NO"（如误输入"YES"，立刻按Cter+C键退出）。在出现"Press RETURN to get started!"提示时，按回车键，进入ROM模式"Router>"。7、键入enable命令进入EXEC状态，键入Router#...
rommon 2 > confreg Configuration Summary enabled are: load rom after netboot fails console baud: 9600 boot: image specified by the boot system commands or default to: cisco2-C3600 do you wish to change the configuration? y/n [n]: y ...