Typeshow run-configto display the config. On a Cisco ASA Firewall: To change terminal line display there are two commands you can use: pager : Sets the number of lines to display in a Telnet session before the "---more---" prompt. This command is saved to the configuration. terminal ...
此外,Cisco IOS CLI資料(show command data)在Catalyst 3850上透過confd軟體進程轉換為YANG格式的資料,然後再作為NETCONF RPC消息傳送到集中管理平台(筆記型電腦) Yang Explorer應用程式。這意味著除使用NETCONF/YANG配置交換機並收集show命令資料外,在Catalyst 3850上仍可使用常規CLI來配置交換機。 1. 資料檢索...
如果在引導序列或show diagnostics module {1|2}命令的輸出中未發現任何硬體故障,請發出show environment status和show environment temperature命令,以檢查與環境條件相關的輸出並查詢其他任何有故障的元件。 cat6knative#show environment statusbackplane: operating clock count: 2 operating VTT count: 3 fan-tray 1:...
resume Resume an active network connection setup Run theSETUPcommand facility show Show running system information ssh Open a secure shell client connection--More-- more表示由于屏幕大小原因,还有部分内容没有显示出来: 回车键:一次向下显示一行 空格键:一次向下显示一屏 特权用户模式转为全局配置模式: 代码语...
4.端口模式 Swtich(config-if)# # 交换机顶层命令 connect 打开终端连接 disable 关闭特权命令 disconnect 断开现有的网络连接 enable 进入特权模式 exit 退出执行 logout 退出执行 ping 发送回应消息 resume 恢复活动的网络连接 show 显示运行系统信息 telnet 打开telnet连接 ...
Step 2. Verify the data stored on the Influx database using the command shown below: root@43f8666d9ce0:~# influx Connected to http://localhost:8086 version 1.7.7 InfluxDB shell version: 1.7.7 > show databases name: databases name --- _internal mdt_gnmi mdt_grpc cisco_mdt mdt_netconf...
Unfortunately I don't have a show vlan brief as I am not at the switch (I should have copied one before I left the office for the day), but I do have a show run. It's not fully configured. I stopped when I realized I couldn't see the vlan's I created. I deleted the vlan'...
路由6.9.1配置ospf与验证 san1#show run!interface Loopback0 ip address 192.168.31.11 255.255.255.255!interface FastEthernet0/0 ip address 192.168.1.1 255.255.255.0 ip ospf message-digest-key 1 md5 cisco ip 配置 职场 ospf 休闲 转载 2008-04-20 23:58:27 270 阅读 ...
Router(config)#service password-encryption将show run中的密码部分做MD5加密 Router(config)#line console 0 Router(config-line)#password cisco Router(config-line)#login 设置CONSOLE口登陆密码为cisco,且只有Login命令打了之后才会生效。(telnet线路为VTY口登陆,方法同样) ...
Depending on the Cisco IOS Software version in use, when SIP is disabled the output from theshow ip socketscommand may still show the SIP ports open, but sending traffic to them will cause the SIP process to emit the following message: ...